Travel on Level Ground - Test - Optional Test
Note: When the procedure for the Travel On Level Ground cannot be performed, this test may be used as a substitute.
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Description     | Qty     |
    | Stopwatch     | 1     |
Show/hide table
Illustration 1 | g00297292 |
- Start the engine.
- Position the machine on level ground.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- Raise a track off the ground. Refer to Illustration 1.
- Put a mark on a shoe of the raised track.
- Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
- Place the travel speed control switch in HIGH position.
- Move the travel lever of the raised track to full travel position.
- Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction.
- Place the travel speed control switch in the LOW position and repeat Steps 8 through 9.
Show/hide table
325C Time For Three Revolutions (time in seconds)     | ||||
---|---|---|---|---|
Travel Speed     | New     | Rebuild     | Service Limit     | |
HIGH     | Forward     | 19.0 or less     | 20.0 or less     | 22 or less     |
Reverse | ||||
LOW     | Forward     | 32.0 or less     | 33.0 or less     | 35.0 or less     |
Reverse |
Show/hide table
325C L Time For Three Revolutions (time in seconds)     | ||||
---|---|---|---|---|
Travel Speed     | New     | Rebuild     | Service Limit     | |
HIGH     | Forward     | 20.5 or less     | 21.5 or less     | 23.5 or less     |
Reverse | ||||
LOW     | Forward     | 35.0 or less     | 36.0 or less     | 38.0 or less     |
Reverse |
Caterpillar Information System:
345B Series II Excavator Additional Messages
330C Excavator Hydraulic System Engine Performance - Test - Engine Speed
VHS10, VHS30, VHS40, VHS50, VHS60 and VHS70 Work Tools Cutters - Inspect/Replace
330C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
330C Excavator Hydraulic System Hydraulic System Pressure - Release
302.5C Mini Hydraulic Excavator Machine System Specifications Blade Lift Cylinder
C9 Engines for Caterpillar Built Machines Cooling System - Test
302.5C Mini Hydraulic Excavator Machine System Specifications Swing Boom Cylinder
C9 Engines for Caterpillar Built Machines Lubrication System
C15 and C18 Engines for Caterpillar Built Machines CID 1421 FMI 09 Unable to communicate with Rear Engine ECM
C9 Engines for Caterpillar Built Machines General Information
M325C Excavator Engine Supplement Oil Pan - Remove and Install - Engine in Chassis
365C Front Shovel Hydraulic System Cylinder Drift - Check - Loaded Bucket
330C Excavator Hydraulic System Travel on Level Ground - Test
345C Material Handler Hydraulic System Return Hydraulic System
330C Excavator Hydraulic System Machine Drift on a Slope - Check
330C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
330C Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
330C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
330C Excavator Hydraulic System Accumulator (Pilot) - Test and Charge
330C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
330C Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
330C Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
302.5C Mini Hydraulic Excavator Machine System Specifications Stick Cylinder