Solenoid Valve (Rotate) - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause future trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision components of the pump or of the motor. All disassembly and all assembly procedures must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and protected at all times.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install new O-ring seals (12) on each solenoid valve group.
Show/hide table
Illustration 1 | g00846341 |
- Install both of the solenoid valve groups in the body. Make sure that each solenoid valve group is installed in the original location which was marked prior to disassembly. Install bolts (11) in order to secure each solenoid valve group. Tighten bolt (11) to a torque of 6.9 ± 0.7 N·m (61 ± 6 lb in).
Show/hide table
Illustration 2 | g00846339 |
- Connect harness assemblies (10) to the solenoid valve groups. Make sure that each harness assembly is connected in the original location that was marked prior to disassembly.
- Install the solenoid valve group (2). Secure the solenoid valve group with bolts (9) .
Show/hide table
Illustration 3 | g00846129 |
- Connect hose assemblies (8), (7), and (6) to the original locations on the bottom of the solenoid valve group. The locations were marked prior to disassembly. Connect hose assemblies (5), (4), and (3) to the original locations on the side of the solenoid valve group. The locations were marked prior to disassembly.
Show/hide table
Illustration 4 | g00985690 |
- Install hood cover (1) near solenoid valve (2) .
Show/hide table
Illustration 5 | g00846128 |
Caterpillar Information System:
303 CR Mini Hydraulic Excavator Fuses - Replace
385C Excavator and 385C Front Shovel Machine System Specifications Bucket Cylinder
385B Excavator Fuel Tank Water and Sediment - Drain
330C Forest Machine Hydraulic System Pump Control (Negative Flow) - Adjust
385B and 5090B Excavators Engine Supplement Muffler - Remove and Install
330C Forest Machine Hydraulic System Pump Control (Output Flow) - Adjust
385B Excavator Machine System Specifications Bucket Cylinder
312C Excavator Machine Systems Solenoid Valve (Rotate) - Remove
303 CR Mini Hydraulic Excavator Fuel Tank Cap and Strainer - Clean
5230B Excavator Machine Systems Bucket Cylinder - Disassemble - Bottom Dump Cylinder for the Front Shovel
5230B Excavator Machine Systems Bucket Cylinder - Disassemble - Front Shovel
5230B Excavator Machine Systems Bucket Cylinder - Disassemble - Mass Excavator
5110B, 5110B L and 5110B MH Excavator Hydraulic System Pilot Manifold
5230B Excavator Machine Systems Pilot Manifold - Install
385B Excavator Fuel Tank Shutoff and Drain Control
385B and 5090B Excavators Machine System Specifications Bucket Cylinder
330C Excavator Machine System Specifications Air Conditioner Lines
5230B Excavator Engine Supplement Radiator - Remove
385B and 5090B Excavators Engine Supplement Electric Starting Motor - Remove and Install
385B and 5090B Excavators Engine Supplement Engine Enclosure Group - Remove and Install
325C Excavator Seat
314D Excavator Window (Front)
308C CR Excavator Window Wiper and Washer Control
325C Excavator Alternate Exit