Rocker Arm - Assemble
组装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
蒸馏燃油发动机
- 检查摇臂中的轴承是否粗糙或磨损。 每个摇臂轴承的内径为70.000 ± 0.015 mm (2.7559 ± 0.0006 in)。
- 检查轴是否粗糙或磨损。 每个摇臂轴承的外径为69.900 ± 0.015 mm (2.7520 ± 0.0006 in)。
- 确保摇臂中用于润滑的油道未被阻塞。
- 将新 O 形密封圈安装在按钮 (5) 中。 将 O 形密封圈涂上清洁的机油。
Show/hide table
图 1 | g01297835 |
- 将按钮 (5) 安装到摇臂上。
- 将干净的发动机油涂抹在组件的摇臂轴 (1) 和摇臂轴承上。
Show/hide table
图 2 | g01297832 |
- 在摇臂轴 (1) 的初始位置安装摇臂 (3) 。
- 将板 (4) 在摇臂轴 (1) 的末端放好,并安装将板 (4) 固定入位的螺栓。
- 将螺栓 (2) 和垫圈安装在摇臂轴 (1) 中。
重质燃油发动机
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-7933     | 螺钉起子     | 1     |
- 检查摇臂中的轴承是否粗糙或磨损。 每个摇臂轴承的内径为70.000 ± 0.015 mm (2.7559 ± 0.0006 in)。
- 检查轴是否粗糙或磨损。 每个摇臂轴承的外径为69.900 ± 0.015 mm (2.7520 ± 0.0006 in)。
- 确保摇臂和摇臂轴中用于润滑的油道未被阻塞。
- 改装工具 (A) 以便安装 O 形密封圈。 改装可以参见图示3。
Show/hide table
图 3 | g00639042 |
- 用清洁的发动机机油润滑嵌件和 O 形密封圈。
Show/hide table
图 4 | g01297891 |
Show/hide table
图 5 | g01297894 |
- 将新的 O 形密封圈置于嵌件上。
- 使用经过改装的工具 (A) 时,握住嵌件末端上的按钮 (5) ,以便将 O 形密封圈推入按钮 (5) 中的凹槽内。 这将把按钮 (5) 安装到摇臂 (3) 上。 请参阅上述的图示。
- 将干净的发动机油涂抹在组件的摇臂轴 (1) 和摇臂轴承上。
Show/hide table
图 6 | g01297832 |
- 在摇臂轴 (1) 的初始位置安装摇臂 (3) 。
- 将板 (4) 在摇臂轴 (1) 的末端放好,并安装将板 (4) 固定入位的螺栓。
- 将螺栓 (2) 和垫圈安装在摇臂轴 (1) 中。
End By: 安装气门机构总成。 请参阅 拆解和组装, "气门机构 - 安装"。
Caterpillar Information System:
3612 and 3616 Engines Rocker Arm - Disassemble
C-10 and C-12 Truck Engines Inlet Manifold
SR4 and SR4B Generators and Control Panels Caterpillar Monitoring System - For Generator Sets with Electromechanical Control Panels for Switchgear Conversion
C-10 and C-12 Truck Engines Air Compressor
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Diagnostic Codes
SR4 and SR4B Generators and Control Panels Electromechanical Control Panel for Switchgear Conversion
SR4 and SR4B Generators and Control Panels Electronic Modular Control Panel II (EMCP II)
C-10 and C-12 Truck Engines Accessory Drive (Air Compressor)
3612 and 3616 Engines Valve Mechanism - Install
SR4 and SR4B Generators and Control Panels Electronic Modular Control Panel II+ (EMCP II+)
G3500 Engines Gas Pressure Regulator - Remove
3126B Marine Engine Engine Crankcase Breather - Clean
C-10 and C-12 Industrial Engines Electrical Ground Stud
330B Excavator Machine System Specifications Recoil Spring
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Remove
SR500 Generators Tools
3612 and 3616 Engines Valve Lifter - Remove
SR4 and SR4B Generators and Control Panels Before Starting Engine
3612 and 3616 Engines Valve Lifter - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
3612 and 3616 Engines Valve Lifter - Disassemble
3612 and 3616 Engines Valve Lifter - Assemble
3126B and 3126E On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3056 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install