Engine Oil Pump - Disassemble
拆解步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1H-3107 | 轴承拉拔器 | 1 |
| 0S-1619 | 螺栓 | 2 | |
| B | 1P-0510 | 冲头总成 | 1 |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清洁发动机机油泵的外部。 在干净的区域拆解发动机机油泵。
- 将护盖 (1) 和护盖 (2) 从发动机机油泵的背部拆下。
Show/hide table
 | |
| 图 1 | g00550544 |
- 垂直放置发动机机油泵。 齿轮应朝上。
- 卸下驱动齿轮 (3) 。 该齿轮驱动燃油输油泵。
Show/hide table
 | |
| 图 2 | g00628384 |
- 将螺栓 (4) 从齿轮 (5) 上松开，直至垫圈距离齿轮为3.20 mm (0.126 in)。
- 安装工具 (A) 。 拧紧工具 (A) 中的螺钉。 敲击轴上方的工具 (A) ，以将齿轮从轴上松开。 拆下工具 (A) 和齿轮 (5) 。
- 拆下盖 (6) 。 注意护盖中定位销的位置。 如有必要，拆下定位销。
Show/hide table
 | |
| 图 3 | g00550546 |
- 如有必要，使用工具 (B) 从盖 (6) 上拆卸轴承 (7) 。 如有必要，将定位销从护盖 (6) 的对侧拆下。
Show/hide table
 | |
| 图 4 | g00550614 |
注: 图示中的轴承带有一个内部凹槽。 发动机机油泵的新轴承不带有一个内部凹槽。
- 将驱动轴 (8) 从泵体 (9) 上拆下。
Show/hide table
 | |
| 图 5 | g00550615 |
- 将惰轮轴 (10) 从泵体 (9) 上拆下。
- 如有必要，将轴承从泵体 (9) 上拆下。
Caterpillar Information System:
EMCPII+ for Gas Engines AL Fault Codes
EMCPII+ for Gas Engines Fault Description
3618 Engine Engine Oil Filler and Oil Level Gauge - Remove and Install
3612 and 3616 Engines Governor Drive - Assemble - Earlier
Installation Of The 174-8943 Sleeve Into The 3408E And 3412E Unit Injector Hydraulic Pump{1714} Installation Of The 174-8943 Sleeve Into The 3408E And 3412E Unit Injector Hydraulic Pump{1714}
Caterpillar Monitoring System for Electronic Modular Control Panel Sensors
C-9 Engines for Caterpillar Built Machines Crankshaft
3054 and 3056 Industrial and Generator Set Engines Fuel Transfer Pump
SR4 and SR4B Generators and Control Panels Manual Operation
3618 Engine Aftercooler - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines AC Offset Adjustment OP10
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Engine Setpoint Verification OP9
3500 Spark Ignited Engines Gas Pressure Regulator
3500B High Displacement Locomotive Engines Electronic Control Module (ECM)
3612 and 3616 Engines Engine Oil Pump - Assemble
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines SP Fault Codes
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Programmable Spare Relay Outputs
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Programmable Spare Output
Caterpillar Monitoring System for Electronic Modular Control Panel Modes Of Operation
C9 On-Highway Truck Engines Unit Injector Hydraulic Pump - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Programmable Kilowatt Level Output
3618 Engine Crankcase Explosion Relief Valve - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Alarm Modules