Engine Oil Pan - Remove and Install
拆卸步骤
Show/hide table
热油和热的部件可能会导致人身伤害。 不要让热油或热的部件与皮肤接触。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 将发动机机油排入合适的容器以便保存或弃置。
- 拆下发动机油底壳 (1) 的螺栓。 拆下发动机油底壳 (1) 。
Show/hide table
图 1 | g00610543 |
典型实例 |
注: 不要撬动或擦伤发动机油底壳的密封面。 必要时,利用橡皮锤轻轻敲打发动机油底壳。
- 将密封垫 (2) 从发动机油底壳 (1) 上拆下。
Show/hide table
图 2 | g00610550 |
典型实例 |
- 将放油塞和 O 形密封圈从发动机油底壳 (1) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-9612     | 硅密封胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将放油塞和 O 形密封圈安装到发动机油底壳上。 将放油塞上紧到 25 ± 5 N·m (18 ± 4 lb ft)。
- 检验密封垫的状况。 必要时,更换密封垫。
注: 在新型发动机上,油底壳采用整体式密封。 检查密封的状态并在必要时更换密封。
- 清理发动机油底壳和缸体的配合面。
Show/hide table
图 3 | g01010643 |
- 将工具 (A) 涂抹到油底壳的 T 形密封垫接头上。 请参阅插图 3。
- 将新密封垫 (2) 和发动机油底壳 (1) 定位到缸体上。
Show/hide table
图 4 | g00610550 |
典型实例 |
Show/hide table
图 5 | g00610543 |
典型实例 |
- 安装发动机油底壳的螺栓。 将螺栓 (X) 上紧到 31 ± 3 N·m (23 ± 2 lb ft) 的扭矩。
Show/hide table
图 6 | g00610574 |
- 从螺栓 (Z) 开始,沿逆时针方向依次上紧其余螺栓。 将其余螺栓上紧到 31 ± 3 N·m (23 ± 2 lb ft) 的扭矩。
- 从螺栓 (Z) 开始,沿逆时针方向重新上紧螺栓。 将螺栓上紧到 31 ± 3 N·m (23 ± 2 lb ft) 的扭矩。
- 向发动机加注机油到正确的油位。 请参阅操作和保养手册,了解正确的加注程序。
Caterpillar Information System:
3126B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
307B Excavator Cab Door
307B Excavator Window (Front)
307B Excavator Drink Holder
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
307B Excavator Ashtray
307B Excavator Lighter
3114, 3116, and 3126 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
307B Excavator Light Switches
307B Excavator Gauges
307B Excavator Plate Locations and Film Locations
307B Excavator Heating and Air Conditioning Control - If Equipped
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seals - Remove and Install
W330B Material Handler Safety Messages
3126B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
307B Excavator Engine Speed Control
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
307B Excavator Blade Control
C-9 Engines for Caterpillar Built Machines Water Temperature Regulator
W330B Material Handler Leaving the Machine
Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490} Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490}
5230 Excavator Hydraulic System Power Shift Pressure - Check
5230B Excavator Hydraulic System Caterpillar Underspeed System - Calibrate