Battery - Remove and Install
Removal Procedure
- Unlock and open access cover (1) on the left side of the machine behind the operator's platform.
Show/hide table
 | |
| Illustration 1 | g00610079 |
- Turn the battery disconnect switch (2) to the OFF position.
Show/hide table
 | |
| Illustration 2 | g00610075 |
- Loosen two knob assemblies (4) and remove battery cover (3) from the machine.
Show/hide table
 | |
| Illustration 3 | g00610076 |
- Disconnect the negative battery cable (5) at the battery.
Show/hide table
 | |
| Illustration 4 | g00610077 |
- Disconnect the jumper cable (6) from the two batteries.
- Disconnect the positive battery cable (7) at the battery.
- Remove four bolts and washers (9) and remove bracket assembly (8) .
Show/hide table
 | |
| Illustration 5 | g00609554 |
- Remove two batteries (10) from the machine. The weight of one battery is 37 kg (82 lb).
Installation Procedure
- Place two batteries (10) in position, as shown. Place bracket assembly (8) in position and install four bolts and washer (9) .
Show/hide table
| | |
| Illustration 6 | g00609554 |
- Connect the positive battery cable (7) at the battery.
Show/hide table
| | |
| Illustration 7 | g00610077 |
- Connect the jumper cable (6) to the two batteries.
- Connect the negative battery cable (5) at the battery.
- Install battery cover (3) and tighten down two knob assemblies (4) .
Show/hide table
| | |
| Illustration 8 | g00610076 |
- Turn the battery disconnect switch (2) to the ON position.
Show/hide table
 | |
| Illustration 9 | g00610146 |
- Close and lock access cover (1) on the left side of the machine behind the operator's platform.
Show/hide table
| | |
| Illustration 10 | g00610079 |
Caterpillar Information System:
W330B Material Handler Equipment Lowering with Engine Stopped
3126B and 3126E On-highway Engines Alternator - Remove and Install
5230 Excavator Hydraulic System True Load Sensing Signal - Test
3064 and 3066 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
C-9 Engines for Caterpillar Built Machines Engine Design
3064 and 3066 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
385B Excavator Safety Messages
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
3064 and 3066 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
365B and 365B Series II Excavators Supplement for 3196 Engine Water Separator - Remove and Install
W330B Material Handler Operating Technique Information
3064 and 3066 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
307B Excavator Operator's Compartment
3064 and 3066 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
307B Excavator Power Receptacle - If Equipped
307B Excavator Monitoring System
A13 Auger Maintenance Interval Schedule
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Boom) - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Boom) - Install
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install