Crankshaft Rear Seal - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6205     | Rear Seal Installer     | 1     |
1P-0510 | Driver Group     | 1     | |
B     | FT-2806     | Alignment Tool     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Engines with 14 Bolt Housing Assembly
- Inspect the condition of the gasket. Replace the gasket, if necessary.
- Clean the areas of the parts that will contact each other.
- Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make sure that you install the seal to the correct depth in the housing. Refer to Specifications, "Crankshaft Seals" for additional information.
Show/hide table
Illustration 1 | g00541839 |
- Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
- Install Tool (A) onto the crankshaft flange.
- Put the new gasket for the housing in position on the dowels in the cylinder block.
- Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
Show/hide table
Illustration 2 | g00606404 |
- Position housing (3) on the dowels in the cylinder block.
- Remove Tool (A) .
- Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
Show/hide table
Illustration 3 | g00606340 |
The flywheel housing has been removed for photographic purposes only. |
- Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
- Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and dirt.
- Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the plastic sleeve after the housing assembly is installed.
Show/hide table
Illustration 4 | g00831176 |
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft flange before installation.
- Place Tool (B) over housing assembly (3). This will center the housing assembly onto the crankshaft flange.
- Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
Show/hide table
Illustration 5 | g00830867 |
- Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine and Machine Warm-Up
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine Starting
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
312B Excavator Machine Systems Travel Brake Valve - Assemble
312B Excavator Machine Systems Travel Brake Valve - Disassemble
P115, P120, P130 and P140 Mechanical Pulverizers Operation
312B Excavator Machine Systems Travel Brake Valve - Install
M318 and M320 Excavators Machine Electronic Control System Switches
312B Excavator Machine Systems Travel Brake Valve-Remove
3046 Engine For Caterpillar Built Machines Crankshaft Gear - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Alternator - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Bottom Guard - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Electric Starting Motor - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Fuel Filter and Water Separator - Remove and Install
307B Excavator Machine Systems Stick Cylinder - Disassemble
302.5 Mini Hydraulic Excavator Engine Supplement Water Pump - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Water Temperature Regulator - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Remove
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Install
302.5 Mini Hydraulic Excavator Engine Supplement Muffler - Remove and Install
307B Excavator Supplement for 4M40 Engine Fuel Priming Pump - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Remove