Travel Brake Valve - Assemble
Assembly Procedure
- Thoroughly clean all of the parts of the travel brake valve prior to assembly.
Note: Make sure that all parts are marked during the disassembly of the travel brake valve. Make sure that the marks are used during the assembly of the travel brake valve. Do not mix the parts.
- Install two relief valve (8) in travel brake valve (2). Tighten two relief valves (8) to a torque of 150 ± 12 N·m (110 ± 9 lb ft).
Show/hide table
Illustration 1 | g00532376 |
This is an exploded view of brake valve (7) . |
Show/hide table
Illustration 2 | g00532374 |
- Install brake valve (7) in travel brake valve (2). Tighten brake valve (7) to a torque of 240 ± 20 N·m (175 ± 15 lb ft).
- Install two check valves (6) in travel brake valves (2). Tighten two check valves (6) to a torque of 150 ± 12 N·m (110 ± 9 lb ft).
- Install valve (5) in travel brake valve (2). Tighten valve (5) to a torque of 20 ± 2 N·m (15 ± 1 lb ft).
- Install brake valve (4) in travel brake valve (2). Tighten brake valve (2) to a torque of 20 ± 2 N·m (15 ± 1 lb ft). Install O-ring seal (3) on the travel brake valve.
Show/hide table
Illustration 3 | g00532372 |
This is an exploded view of brake valve (4) . |
Show/hide table
Illustration 4 | g00529096 |
- Install plate (1) on travel brake valve (2) .
Show/hide table
Illustration 5 | g00529095 |
End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve - Remove and Install" in this manual.
Caterpillar Information System:
312B Excavator Machine Systems Travel Brake Valve - Disassemble
P115, P120, P130 and P140 Mechanical Pulverizers Operation
312B Excavator Machine Systems Travel Brake Valve - Install
M318 and M320 Excavators Machine Electronic Control System Switches
312B Excavator Machine Systems Travel Brake Valve-Remove
3046 Engine For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3046 Engine For Caterpillar Built Machines Gear Group (Front) - Install - Idler Gear Only
312B Excavator Machine Systems Final Drive - Install
3054 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
312B Excavator Machine Systems Final Drive - Remove
M318 and M320 Excavators Machine Electronic Control System Engine and Hydraulic Pump Controller
3054 Engine for Caterpillar Built Machines V-Belts - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine Starting
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine and Machine Warm-Up
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
302.5 Mini Hydraulic Excavator Engine Supplement Alternator - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Bottom Guard - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Electric Starting Motor - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Fuel Filter and Water Separator - Remove and Install
307B Excavator Machine Systems Stick Cylinder - Disassemble
302.5 Mini Hydraulic Excavator Engine Supplement Water Pump - Remove and Install