Travel Brake Valve - Install
Installation Procedure
- Make sure that the mating surfaces of the travel motor and the travel brake valve are thoroughly clean.
- Check the condition of the three O-ring seals that are used between the travel motor and the travel brake valve. If the O-ring seals are damaged, use new parts for replacement.
- Install the three O-ring seals in the travel motor.
- Place travel brake valve (3) in position on the travel motor. Install six bolts (4). Tighten the six bolts to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
Show/hide table
Illustration 1 | g00483963 |
- Check the condition of the O-ring seals that are used in the ends of two hose assemblies (5). If the O-ring seals are damaged, use new parts for replacement.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Connect two hose assemblies (5) to the travel brake valve. Tighten the hose assemblies to a torque of 80 ± 7 N·m (60 ± 5 lb ft).
- Fill the hydraulic oil tank with hydraulic oil to the correct level.
Note: Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities" for the proper filling procedure and the proper levels for the hydraulic system.
- Start the machine and check for leaks. Check the operation of the travel motors.
- Install cover (2). Install the washers and four bolts (1). Tighten the four bolts to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Show/hide table
Illustration 2 | g00483962 |
Caterpillar Information System:
M318 and M320 Excavators Machine Electronic Control System Switches
312B Excavator Machine Systems Travel Brake Valve-Remove
3046 Engine For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3046 Engine For Caterpillar Built Machines Gear Group (Front) - Install - Idler Gear Only
312B Excavator Machine Systems Final Drive - Install
3054 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
312B Excavator Machine Systems Final Drive - Remove
M318 and M320 Excavators Machine Electronic Control System Engine and Hydraulic Pump Controller
3054 Engine for Caterpillar Built Machines V-Belts - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Spacer Plate - Remove and Install
307B Excavator Supplement for 4M40 Engine Air Conditioner Dryer - Remove and Install
307B Excavator Supplement for 4M40 Engine Crankshaft Vibration Damper and Pulley - Remove and Install
P115, P120, P130 and P140 Mechanical Pulverizers Operation
312B Excavator Machine Systems Travel Brake Valve - Disassemble
312B Excavator Machine Systems Travel Brake Valve - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine Starting
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine and Machine Warm-Up
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
302.5 Mini Hydraulic Excavator Engine Supplement Alternator - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Bottom Guard - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Electric Starting Motor - Remove and Install