Engine Oil Filler and Oil Level Gauge - Remove and Install
拆卸步骤
- 断开软管组件 (6) (如有配备)。 拆下加注口和加注口油位表上的盖 (1) 。 拆下 O 形密封圈。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g00612376 |
Show/hide table
图 2 | g00612378 |
Show/hide table
图 3 | g00612379 |
- 从管组件 (2) 拆下油尺。
- 拆下螺栓 (3) 和螺栓 (12) ,以拆下管组件 (8) 。
- 拆下螺栓 (9) 。 拆下管路组件 (10) 。
- 拆下弯管和盖 (4) 。
- 如果发动机配备接触器组件,则应按照以下步骤:
- 拆下螺钉 (5) 。 重新安置盖。 拆下将盒 (7) 固定于盖 (1) 上的螺钉。 断开接头 (11) 。
- 拆下螺栓 (13) 。 拆下螺栓 (16) 。 断开接头 (14) 。 松开螺母 (15) 。 断开油位开关并拆下油位开关。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3413     | 管密封胶     | -     |
B     | 5N-5561     | 硅树脂润滑脂     | -     |
- 如果发动机配备接触器组件,则应按照以下步骤:
- 安装油位开关。 拧紧螺母 (15) 并连接接头 (14) 。 安装螺栓 (16) 。 安装螺栓 (13) 。
- 连接接头 (11) 。 安装将盒 (7) 固定于盖 (1) 上的螺钉。 将盖放置到位后,安装螺钉 (5) 。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 4 | g00612379 |
Show/hide table
图 5 | g00612378 |
Show/hide table
图 6 | g00612376 |
- 安装弯管和盖 (4) 。
- 安装管组件 (10) 并拧紧螺栓 (9) 。
- 安装管路组件 (8) 。
- 将工具 (A) 涂敷在螺栓 (12) 和螺栓 (3) 的螺纹上。 安装螺栓 (12) 和螺栓 (3) 。
- 将油尺安装在管组件 (2) 上。
- 将新的 O 形密封圈安装在盖 (1) 。 使用工具 (B) 将 O 形密封圈固定到位。
- 安装盖 (1) 。 安装软管组件 (6) (如有配备)。
Caterpillar Information System:
3126B Truck Engine Housing (Front) - Install
C-9 Engines for Caterpillar Built Machines Exhaust Manifold
3524B Engine for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3126B Engines for Caterpillar Built Machines Housing (Front) - Remove
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Flywheel Housing - Install
SR4B Generators Glossary
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Flywheel Housing - Remove
C-9 Engines for Caterpillar Built Machines Crankshaft Seals
3612 and 3616 Engines Engine Oil Filler and Oil Level Gauge - Remove and Install
SR4B Generators Component Descriptions
SR4B Generators General Information
C-15, C-16 and C-18 Truck Engines Engine Oil Filter Base - Remove
3500B Engines Camshaft
C-15, C-16 and C-18 Truck Engines Engine Oil Filter Base - Install
G3304 and G3306 Engines Crankshaft
C-9 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3126B and 3126E On-highway Engines Fuel Transfer Pump - Remove
3612 and 3616 Engines Crankcase Explosion Relief Valve - Remove and Install
3524B Engine for Caterpillar Built Machines Crankshaft Main Bearings - Install
3500 Engines for Caterpillar Built Generator Sets Vibration Damper
C-9 Industrial Engine Flywheel Housing
3512B Marine Auxiliary Engine Housing (Front)
3126B and 3126E On-highway Engines Front Cover - Remove
3612 and 3616 Engines Water Temperature Regulator - Remove and Install