PRODUCT SUPPORT PROGRAM FOR REMOVING AIR CONDITIONING PRESSURE SWITCHES FROM DEALER STOCK
Usage:
REBE2222-00
Show/hide table
| 18Jul2007 |
U-336
A-276
D-282
O-305
Show/hide table
| Parts stock action only | PRODUCT SUPPORT PROGRAM FOR REMOVING AIR CONDITIONING PRESSURE SWITCHES FROM DEALER STOCK |
|
| 1808 1408 7320 1802 7750 | PI70236 |
|
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst. |
Show/hide table
Show/hide table
Show/hide table
TERMINATION DATE |
| 31Oct2007 |
PROBLEM
Show/hide table
| A Manufacturing Problem with switches in the affected date code could cause the switch to open after being heat cycled. This will result in the AC compressor not turning on when the system has adequate pressure. |
ACTION REQUIRED
Show/hide table
| Sort Stock and remove the 114-5333, 114-5334, and 180-5462 Switches with the four digit date code range of 6152 - 6334 (image 1) from dealer stock. The date code will be in the form of NNNNXX, where NNNN is the date code you are sorting for. Disregard the letters (XX). |
Show/hide table
|
| Image1 |
SERVICE CLAIM ALLOWANCES
Show/hide table
| Submit one claim for all parts removed from dealer parts stock. |
PARTS DISPOSITION
Show/hide table
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
Caterpillar Information System:
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REINSTALLING, IF NECESSARY, THE COUPLING HUB ON CERTAIN 330DL EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REINSTALLING, IF NECESSARY, THE COUPLING HUB ON CERTAIN 330DL EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM ON CERTAIN M325C AND M325D MATERIAL HANDLERS PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM ON CERTAIN M325C AND M325D MATERIAL HANDLERS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE WIRING HARNESS FOR THE ENGINE AIR HEATER RELAY ON CERTAIN 320D, 320D L, AND 323D LN EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE WIRING HARNESS FOR THE ENGINE AIR HEATER RELAY ON CERTAIN 320D, 320D L, AND 323D LN EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE CYLINDER GUARDS ON CERTAIN 365B, 365C, 5090B AND 385C FRONT SHOVEL EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REWORKING THE CYLINDER GUARDS ON CERTAIN 365B, 365C, 5090B AND 385C FRONT SHOVEL EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSPECTING AND REPLACING IF NECESSARY THE SWING DRIVE BOLTS ON CERTAIN 330D L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSPECTING AND REPLACING IF NECESSARY THE SWING DRIVE BOLTS ON CERTAIN 330D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING A TUBE ASSEMBLY FOR THE AIR CONDITIONING SYSTEM ON CERTAIN FORESTY EXCAVATORS AND TRACK FELLER BUNCHERS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING A TUBE ASSEMBLY FOR THE AIR CONDITIONING SYSTEM ON CERTAIN FORESTY EXCAVATORS AND TRACK FELLER BUNCHERS
PRODUCT SUPPORT PROGRAM FOR PROVIDING SPECIAL APPLICATION BOOMS FOR CERTAIN 345B, 345B II, 345BL II, AND 345C HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR PROVIDING SPECIAL APPLICATION BOOMS FOR CERTAIN 345B, 345B II, 345BL II, AND 345C HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE STICK ON CERTAIN 385C L MATERIAL HANDLERS USED IN BARGE APPLICATIONS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE STICK ON CERTAIN 385C L MATERIAL HANDLERS USED IN BARGE APPLICATIONS
PRODUCT SUPPORT PROGRAM FOR ELIMINATING WHITE SMOKE ON CERTAIN 315C HYDRAULIC EXCAVATORS EQUIPPED WITH THE 3046 ENGINE PRODUCT SUPPORT PROGRAM FOR ELIMINATING WHITE SMOKE ON CERTAIN 315C HYDRAULIC EXCAVATORS EQUIPPED WITH THE 3046 ENGINE
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING, AND IF NECESSARY REPLACING, THE 179-2203 OUTER BOLTS OF THE SWING GEAR BEARING ON CERTAIN 365B, 365B SERIES II, AND 365C EXCAVATORS THAT ARE CONFIGURED FOR MATERIAL HANDLING, ULTRA HIGH DEMOLITION OR OEMS A PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING, AND IF NECESSARY REPLACING, THE 179-2203 OUTER BOLTS OF THE SWING GEAR BEARING ON CERTAIN 365B, 365B SERIES II, AND 365C EXCAVATORS THAT ARE CONFIGURED FOR MATERIAL HANDLING, ULTRA HIGH DEMOLITION OR OEMS A
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE HARNESS INSTALLATION ON CERTAIN 324D L AND 325D L EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE HARNESS INSTALLATION ON CERTAIN 324D L AND 325D L EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING FAILED CONTROL GROUP HANDLE (227-7616 OR 227-7617) USED ON CERTAIN 312D, 315D, 319D, 320D, 323D, 324D, 325D, 330D, 345D, 345C, 365C, 365C FS, 385C, 385C FS, 324D FM, 325D FM, 330D FM, 325D MH, 330D MH, 365C MH, 3 PRODUCT SUPPORT PROGRAM FOR REPLACING FAILED CONTROL GROUP HANDLE (227-7616 OR 227-7617) USED ON CERTAIN 312D, 315D, 319D, 320D, 323D, 324D, 325D, 330D, 345D, 345C, 365C, 365C FS, 385C, 385C FS, 324D FM, 325D FM, 330D FM, 325D MH, 330D MH, 365C MH, 3
PRODUCT SUPPORT PROGRAM FOR INSTALLING GUSSETS ON CERTAIN DEMOLITION AND SCRAP SHEARS. CATERPILLAR MODELS S365B, S385B, AND VERACHTERT MODELS VHS-60/3, AND VHS-70/3. PRODUCT SUPPORT PROGRAM FOR INSTALLING GUSSETS ON CERTAIN DEMOLITION AND SCRAP SHEARS. CATERPILLAR MODELS S365B, S385B, AND VERACHTERT MODELS VHS-60/3, AND VHS-70/3.
PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C L AND 330D L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C L AND 330D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM TO TIGHTEN THE SWING GEAR AND BEARING MOUNTING BOLTS ON CERTAIN 324D, 324D FM, 324D MH, 325D, 325D FM, 325D MH, 330D, 330D FM, 330D MH, 345C, AND 345C MH EXCAVATORS PRODUCT IMPROVEMENT PROGRAM TO TIGHTEN THE SWING GEAR AND BEARING MOUNTING BOLTS ON CERTAIN 324D, 324D FM, 324D MH, 325D, 325D FM, 325D MH, 330D, 330D FM, 330D MH, 345C, AND 345C MH EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM LOWERING CHECK VALVES ON CERTAIN 312C, 315C, 318C, AND 319C EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM LOWERING CHECK VALVES ON CERTAIN 312C, 315C, 318C, AND 319C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE CROSSOVER RELIEF VALVE ON CERTAIN M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, M318, M318C, M318D, M320, M322C, AND M322D WHEELED EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE CROSSOVER RELIEF VALVE ON CERTAIN M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, M318, M318C, M318D, M320, M322C, AND M322D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE EDGE ASSEMBLY ON CERTAIN 365 (FRONT SHOVEL) AND 385 EXCAVATOR BUCKETS WITH BUCKET PREFIX H1A. PRODUCT SUPPORT PROGRAM FOR REPLACING THE EDGE ASSEMBLY ON CERTAIN 365 (FRONT SHOVEL) AND 385 EXCAVATOR BUCKETS WITH BUCKET PREFIX H1A.
PRODUCT IMPROVEMENT PROGRAM FOR TIGHTENING THE TURBO HOSE CLAMP ON CERTAIN 323D EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR TIGHTENING THE TURBO HOSE CLAMP ON CERTAIN 323D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE HYDRAULIC ROTATOR ON CERTAIN GSH15 GRAPPLES (PREFIX HGK, TOPLEVEL 231-0203) PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE HYDRAULIC ROTATOR ON CERTAIN GSH15 GRAPPLES (PREFIX HGK, TOPLEVEL 231-0203)
PRODUCT SUPPORT PROGRAM FOR REPLACING THE RADIATOR SERVICE DOOR ON CERTAIN 324D, 325D AND 325DL EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE RADIATOR SERVICE DOOR ON CERTAIN 324D, 325D AND 325DL EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REMOVING THE CHECK VALVE IN THE QUICK COUPLER LINE ON CERTAIN 320C, 322C, 325C, 330C, 320D, 324D, 325D, 330D, AND 345C EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REMOVING THE CHECK VALVE IN THE QUICK COUPLER LINE ON CERTAIN 320C, 322C, 325C, 330C, 320D, 324D, 325D, 330D, AND 345C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR CHANGING TWO PORTS ON THE MEDIUM PRESSURE SWIVEL ON CERTAIN M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318D, M322C, M322D, M325C, AND 325D WHEELED EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR CHANGING TWO PORTS ON THE MEDIUM PRESSURE SWIVEL ON CERTAIN M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318D, M322C, M322D, M325C, AND 325D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING A NEW BOOM ASSEMBLY ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSTALLING A NEW BOOM ASSEMBLY ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS