New Work Tool Hose Installation Method Is Now Used on Certain Skid Steer Loaders {5057}
- Skid Steer Loader
- 216B Series 3 (S/N: HR21-248; PWK1-2650)
- 226B3 (S/N: DXZ1-1824)
Description Of Change: A new work tool hose installation method is now used on the sales models listed above. The new installation method prevents hose interference with the tires which can lead to hose damage.
Adaptable To: The following parts are adaptable to the machines within the listed serial numbers, and are effective with all machines after the listed serial numbers.
Perform the following steps to ensure the hoses are installed properly.
Show/hide table
 |
|
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. |
- With the bucket installed, identify the top and bottom hoses. Ensure both hoses are routed through the D-link and that there is no slack in the hoses from the D-link to the bucket.
Show/hide table
Illustration 2 g06310077 - Ensure that the hoses are not twisted at any point from connection to connection. Adjust the hoses as necessary.
Show/hide table
Illustration 3 g06310083 - Connect the hoses to the auxiliary ports at the front side of the bucket.
Show/hide table
| |
| Illustration 1 | g06310076 |
Caterpillar Information System:
An Improved Oil Level Gauge Assembly (Dipstick) Is Now Used on Certain 950K, 950L, 950M, 962K, 962L, and 962M Medium Wheel Loaders {1326} An Improved Oil Level Gauge Assembly (Dipstick) Is Now Used on Certain 950K, 950L, 950M, 962K, 962L, and 962M Medium Wheel Loaders {1326}
3516E Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Final Drive Oil (Rear) - Change
A Lanyard to Secure Operation and Maintenance Manual Is Now Used on Certain 740 EJ and 745 Articulated Trucks {0374, 7312} A Lanyard to Secure Operation and Maintenance Manual Is Now Used on Certain 740 EJ and 745 Articulated Trucks {0374, 7312}
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel Pump (High Pressure) - Remove and Install
785C Off-Highway Trucks Equipped with Dynamic Gas Blending (DGB) Welding on Machines and Engines with Electronic Controls
G3512 Gas Engine Electric Starting Motor
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Oil Level Is Low
826K Landfill Compactor Prepare the Machine for Maintenance
Improved A/C Compressor Is Now Available on Certain Large Wheel Loaders and Large Wheel Dozers {1802} Improved A/C Compressor Is Now Available on Certain Large Wheel Loaders and Large Wheel Dozers {1802}
C9.3B Engines Inlet Manifold Air Pressure Sensor
C9.3B Engines Atmospheric Pressure Sensor
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Turbocharger
24 Motor Grader Systems Oil Filter (Hydraulic Return)
A Hose Clamp May Fail in the Heater Lines Group on Certain 770G, 772G, 773G, 775G, and 777G Off-Highway Trucks {1380, 1808, 1812, 7304} A Hose Clamp May Fail in the Heater Lines Group on Certain 770G, 772G, 773G, 775G, and 777G Off-Highway Trucks {1380, 1808, 1812, 7304}
The Heater Control Group in the Air Conditioning Group May Fail on Certain 773E and 777E Off-Highway Trucks {7304} The Heater Control Group in the Air Conditioning Group May Fail on Certain 773E and 777E Off-Highway Trucks {7304}
Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266} Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266}
Snow Push and Plows Work Tool Supplement Plate Locations and Film Locations
Snow Push and Plows Work Tool Supplement Side Plate Skid Plate - Inspect/Replace
2D GRADE System for 24 Next Gen Motor Graders Electrical Power Supply - Test
Snow Push and Plows Work Tool Supplement Springs - Inspect/Replace
C9.3 Engine for Caterpillar Built Machines Fuel Transfer Pump
24 Motor Grader Drawbar Ball and Socket End Play - Check/Adjust
MD6200 Rotary Drill Prepare the Machine for Maintenance