| |
| Illustration 1 | g03413585 |
|
Console on the right side of the machine (1) IQAN-Md3 (2) Right-Hand Joystick (3) Engine Start Switch (4) Heating and Air Conditioning Controls (5) 12V Power Receptacles (6) Cup Holders (7) Control Panel | |
| |
| Illustration 2 | g02647097 |
|
(8) Foot Rest
(9) Service Brake (10) Travel Pedal REVERSE (11) Travel Pedal FORWARD | |
| |
| Illustration 3 | g03413756 |
|
(12) Parking Brake
(13) Hydraulic Arming Control (14) Throttle Up Control (15) Active Regeneration Indicator (16) Front Floodlight Control (17) Pump Displacement Switch (18) Horn Control (19) Fan Directional Control (20) Saw Control (21) Throttle Down Control (22) Active Regeneration Disable Control (23) Rear Floodlight Control (24) Differential Lock Control (25) Manual Hydraulic Over Ride Control (26) Winch Retract (27) Winch Release | |
| |
| Illustration 4 | g03667695 |
(28) Left-Hand Joystick.
| |
| Illustration 5 | g02647268 |
The cab dome light is on the ceiling of the cab above the operator.
| |
| Illustration 6 | g03688895 |
IQAN-Md3 Display (1) is on the right side console in the cab.
The IQAN-MD3 module consists of a display, nine buttons. This module is on the right switch panel in the front of the cab. The IQAN-MD3 allows individual functions of the machine to be displayed. The IQAN-MD3 allows you to adjust several implement functions. The IQAN-MD3 monitors all the input signals and all the output signals.
The IQAN-MD3 allows the operator to obtain different machine information. The monitor is also used for adjusting the hydraulic settings, calibrating machine controls, testing machine components, and troubleshooting machine systems.
Note: Most of the troubleshooting of the IQAN system and machine system can be performed with the use of the IQAN-MD3 module.
The IQAN-MD3 processes incoming CAN Bus signals, the digital on/off signals, and the voltage input signals. Module converts the signals into functions and the module sends the signals to the solenoids and the CAN Bus signals to the other control units.
| |
| Illustration 7 | g03667706 |
| |
| Illustration 8 | g03688897 |
The right joystick controls the accumulator arms, the lift, and the tilt of the felling head, the float function, and the temporary differential lock. The middle left button on the top of the right joystick closes the accumulator arms. The middle right button on the top of the right joystick opens the accumulator arms.
The middle low button on the joystick activates the float function. the side buttons on the right underside of the joystick control the float intensity. Use the upper button to increase intensity, lower button to decrease intensity.
The lower right button and the top right buttons on the top of the right joystick are the boom float function.
To temporarily engage the front differential lock, hold the toggle switch on the joystick. To disengage the front differential lock, release the toggle switch.
Note: The momentary differential lock switch will only function if the front differential lock switch and the rear differential lock switch are in the OFF position.
|
OFF - When you insert the engine start switch key and when you remove the engine start switch key, the engine start switch must be in the OFF position. To disconnect the power to the electrical circuits in the cab, turn the engine start switch to the OFF position. Also, turn the engine start switch to the OFF position to stop the engine. |
|
ON - To activate the electrical circuits in the cab, turn the engine start switch key clockwise to the ON position. |
|
START - To start the engine, turn the engine start switch clockwise to the START position. When the engine start switch key is released, the engine start switch will return to the ON position. |
Note: If the engine fails to start, return the engine start switch to the OFF position. This must be done before you attempt to start the engine again.
Heating and Air Conditioning Controls (4)
| |
| Illustration 9 | g02647839 |
The control panel for the heating and air conditioning system is on the right side of the cab.
On/Off Switch (A) Turns the heater or Air Conditioner on and off.
|
Cooling - Turn knob (B) counterclockwise to decrease the temperature in the cab. |
|
Heating - Turn knob (B) clockwise to increase the temperature in the cab. |
|
Fan Speed Switch - Fan speed switch (C) controls the speed of the blower fan motor for the heating and air conditioning system. Turn the knob clockwise for more air. Turn the knob counterclockwise for less air. |
| |
| Illustration 10 | g02647923 |
The Control Panel is on the right side console in the cab.
Foot Brake Control (Service) (9)
| |
| Illustration 11 | g02647998 |
Service brake pedal (9) is the center pedal on the cab floor.
Depress the service brake pedal to slow the machine ground speed. Use the service brake pedal for normal braking.
|
| |
| Illustration 12 | g02647998 |
The direction of the machine is determined by travel pedals (10) and (11).
When you depress travel pedal (10), the machine will travel in the REVERSE direction.
When you depress travel pedal (11) the machine will travel in the FORWARD direction.
When both of the travel pedals are released, the engine speed will slow.
Depress the center brake pedal to slow or stop the machine.
| NOTICE |
|---|
|
Do not engage the parking brake while the machine is moving unless the service brake fails. The use of the parking brake as a service brake in regular operation will cause severe damage to the parking brake. |
| |
| Illustration 13 | g02649240 |
|
Parking Brake - Parking brake switch (12) is on the right side console. Use the parking brake only after the machine is stopped. |
Depress switch to activate the parking brake. Parking brake switch indicator (12) will be illuminated when the parking brake is engaged.
Depress switch to turn off the parking brake. Parking brake switch indicator (12) will go off. Release the switch when the parking brake deactivates.
Note: To deactivate the parking brake, the hydraulic system must be armed.
| |
| Illustration 14 | g02649316 |
The hydraulic arming control (13) is used to turn the machine hydraulic system (implement and steering) on and off. The hydraulic arming control is on the right side of the operator seat.
When the hydraulic arming control activation light is ILLUMINATED, the machine hydraulic system is on.
When the hydraulic arming control activation light is NOT ILLUMINATED, the machine hydraulic system is off.
Throttle Up Speed Control (14)
| |
| Illustration 15 | g02649337 |
This valve controls the ground speed by regulating the signal pressure to the propel pump.
Depress switch (14) to increase engine speed.
Active Regeneration Control (15)
| |
| Illustration 16 | g02649343 |
Depress switch (15) for 2-3 seconds to activate regeneration function (ARD).
| |
| Illustration 17 | g02649437 |
Depress the switch (16) to turn the front lights ON. Depress the switch again to turn the front lights OFF.
| |
| Illustration 18 | g02650718 |
Depress the switch (17) to select motor displacement. Depress the switch to select maximum displacement pressure, and disable auto shift function.
| |
| Illustration 19 | g02649457 |
Depress the switch (18) to sound the horn. Repeatedly depress the switch to sound the horn again.
| |
| Illustration 20 | g02649476 |
The direction of the fan can be reversed. This will clear debris from the radiator. The switch (19) is located in the right side console. Operate the switch to reverse the fan. Release the switch to stop the reverse direction of the fan.
| |
| Illustration 21 | g02649499 |
Implement switch (20) is on the right side console in the cab.
Depress the implement switch to activate the implement function.
Depress the implement switch again to deactivate the implement function.
Note: The implement functions will only operate if the hydraulic lockout control is in the ON position, with light ILLUMINATED.
Note: Implement function pressure is displayed on the IQAN-Md3 main screen. Display indicates the hydraulic oil pressure to the implement . If the pressure is high, the speed of the implement function is slow. If the pressure is low, the speed of the implement is high. When the pressure is high and the implement function is slow, you may choose to limit another function such as the travel, the lift or the steer in order for the saw to recover faster.
Throttle Down Speed Control (21)
| |
| Illustration 22 | g02649502 |
This valve controls the engine speed by regulating the signal pressure to the propel pump.
Depress switch (21) to decrease engine speed.
Regeneration Disable Control (22)
This function will deactivate the ARD.
| |
| Illustration 23 | g02649505 |
Depress switch (22) to deactivate regeneration function.
| |
| Illustration 24 | g02649507 |
Depress the switch (23) to turn the rear lights ON. Depress the switch again to turn the rear lights OFF.
Differential Lock Control (24)
| |
| Illustration 25 | g02649509 |
The rear differential lock switch (24) is on the right side panel.
Press rear differential lock switch (24) to engage the rear differential lock. When the differential lock is engaged, both wheels on the axle will turn at the same speed.
The momentary front differential lock switch is on the right joystick. Squeeze and hold the momentary front differential lock switch to activate the differential lock. Release the momentary differential lock switch to deactivate the front differential lock.
Indicator will illuminate on the IQAN-Md3 display and light on control panel will illuminate when the differential lock is engaged.
Hydraulic Override Control(25)
| |
| Illustration 26 | g02649517 |
The hydraulic override switch (25) is on the right side panel.
Press and hold hydraulic override switch to enable the "limp" home hydraulic functions. Functions that will be enabled are propel, steer, and raise or lower the arm.
| |
| Illustration 27 | g03413776 |
The winch retract switch (26) is on the right side panel.
Press the winch retract switch to spool the winch cable back onto the winch.
| |
| Illustration 28 | g03413826 |
The winch spool switch (27) is on the right side panel.
Press the winch spool switch to release the winch cable.
The momentary front differential lock toggle switch is on the right joystick. Squeeze the momentary front differential lock switch to activate the front differential lock. Release the momentary front differential lock switch to deactivate the front differential lock.
| |
| Illustration 29 | g03688904 |
The right joystick controls the implement function, float function and differential lock function for this machine.
(A) Move the joystick to this position to tilt the implement downward.
(B) Move the joystick to this position to raise the implement.
(C) Move the joystick to this position to tilt the implement upward.
(D) Move the joystick to this position to lower the implement.
(E) Press the switch to open the collector arms.
(F) Press the switch to close collector arms.
(G) Press the switch to activate front differential lock function.
| |
| Illustration 30 | g06203455 |
(H) Press this switch to activate the boom float function.
(I) Press the switch to increase pressure of the boom float.
(J) Press switch to decrease pressure of the boom float .
| |
| Illustration 31 | g03688938 |
The left joystick controls the steering for this machine.
(A) Move the joystick to this position to steer the machine to the right.
(B) Move the joystick to this position to steer the machine to the left.
The joystick will return to the center when the joystick is released. However, the machine will not straighten as the joystick returns to the center position. You must steer the machine in the opposite direction to straighten the machine.
(C) Press the switch to open gather arms.
(D) Press the switch to close gather arms.
(E) Press the switch to open all arms.
(F) Press the switch totemporarily slow machine speed.