Stopping the Engine
Show/hide table
| NOTICE |
|---|
|
Stopping the engine immediately after it has been working under load, can result in overheating and accelerated wear of the engine components. See the following stopping procedure, to allow the engine to cool, and to prevent excessive temperatures in the turbocharger center housing, which could cause oil cooking problems. |
- Before stopping the engine, allow the engine to run at low idle for 5 minutes. The engine must idle with no load. This procedure allows the hot areas of the engine to cool gradually. This procedure extends the life of the engine.
- Be sure that all the controls are in the OFF position. Be sure that all the controls are in the proper position for parking the machine.
- Turn the engine start switch to the OFF position. Remove the key.
Caterpillar Information System:
994K Large Wheel Loader Field Assembly Manual Automatic Lubrication - Install
PM-102 Cold Planer Stopping the Machine
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Blade - Remove and Install
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
Procedure For Connecting To The Spare Fuses on F2 Series Backhoe Loaders {1417, 1422} Procedure For Connecting To The Spare Fuses on F2 Series Backhoe Loaders {1417, 1422}
New Mounting Plates for the ROPS Support Strut are Now Used on Certain B Series Compactors {7323} New Mounting Plates for the ROPS Support Strut are Now Used on Certain B Series Compactors {7323}
New Hose Assemblies and Clips are Now Used in the Fuel Lines on Certain 14M Motor Graders {1274} New Hose Assemblies and Clips are Now Used in the Fuel Lines on Certain 14M Motor Graders {1274}
AP500F, AP555F, AP600F, AP655F, AP655F L, AP1000F and AP1055F Asphalt Pavers and SE50 and SE60 Asphalt Screeds Operator Control Switch (Switch to Battery) - Test
AP600F Asphalt Paver Machine Systems Electrical System (Auxiliary Hydraulic)
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Engine Rear Mount - Remove and Install
An Improved Plate Assembly within Hydraulic Control Groups is Now Used on Certain 416E Backhoe Loaders {5063} An Improved Plate Assembly within Hydraulic Control Groups is Now Used on Certain 416E Backhoe Loaders {5063}
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Engine Front Mount - Remove and Install
PM-102 Cold Planer Stopping the Engine if an Electrical Malfunction Occurs
PM-102 Cold Planer Towing the Machine
PM-102 Cold Planer Parking Brake Manual Release
PM-102 Cold Planer Machine Cleanup Procedure
Loader Arm Issues {6118, 6119} Loader Arm Issues {6118, 6119}
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Blade Cylinder - Remove and Install
A New Recommendation For Cylinder Cut Out Testing Is Now Used on Certain 12K, 120K, 120K 2, 120K 2 OEM, 140K, 140K 2, and 160K Motor Grader Engines {7000} A New Recommendation For Cylinder Cut Out Testing Is Now Used on Certain 12K, 120K, 120K 2, 120K 2 OEM, 140K, 140K 2, and 160K Motor Grader Engines {7000}
994K Large Wheel Loader Field Assembly Manual Cooling System Package Lines and Wiring - Connect
New Software Installation Procedure For VIMS Module On Certain Motor Graders {7601, 7610, 7620} New Software Installation Procedure For VIMS Module On Certain Motor Graders {7601, 7610, 7620}
415F2 Backhoe Loaders Hydraulic and Steering System Lines (Hydraulic)
Technical Analysis 1 (TA1) Visual Inspection for Backhoe Loaders {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Backhoe Loaders {0372, 1000, 7000, 753T, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}