Bucket Positioner Control - Remove and Install - Single Tilt
- Remove pin (1) and yoke assembly (2).
Show/hide table
Illustration 2 g02848503 - Remove bolts (3) and tube assembly (4).
Show/hide table
Illustration 3 g01523982 Show/hide tableIllustration 4 g01523987 - Remove bolts (6) and reposition bracket assembly (5) (not shown).
- Loosen nut (9). Disconnect harness assemblies (7) from roller switch assembly (8). Remove roller switch assembly (8) from bracket assembly (5).
Show/hide table
Illustration 1 | g02848499 |
- Install the bucket positioner control in the reverse order of removal.
- Tighten nut (9) to a torque of
18.5 ± 5.0 N·m (164 ± 44 lb in) .
- Tighten nut (9) to a torque of
- Adjust the bucket positioner control. Refer to Specifications, "Bucket Positioner and Lift Kickout".
Caterpillar Information System:
2015/05/04 New Plates in the Heat Insulation Group are Now Used on Certain 773G and 775G Quarry Trucks {7150, 7150, 7150, 7251, 7301, 7329}
Mirrors with Improved Tempering Process May Break on Certain Off-Highway Trucks and Quarry Trucks{7319} Mirrors with Improved Tempering Process May Break on Certain Off-Highway Trucks and Quarry Trucks{7319}
GSH420, GSH425, GSH440, GSH455, GSH520, GSH525 and GSH555 Orange Peel Grapples Specifications
GSH420, GSH425, GSH440, GSH455, GSH520, GSH525 and GSH555 Orange Peel Grapples Safety Messages
735, 740 GC, 740 EJECTOR, 745 Articulated Trucks Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
Bench Test Procedure for 735C, 740C, 745C, 740 Ejector, 745, and 740 GCArticulated Truck Transmission {3030, 3073, 3167} Bench Test Procedure for 735C, 740C, 745C, 740 Ejector, 745, and 740 GCArticulated Truck Transmission {3030, 3073, 3167}
C4.4 and C7.1 Engines Test ECM Mode
AP600F Asphalt Pavers Machine Systems Diesel Exhaust Fluid Lines
C7.1 Engines Codes that Inhibit Operation of Aftertreatment System
735, 740 GC, 740 EJECTOR, 745 Articulated Trucks Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
AP655F and AP655F L Asphalt Paver Machine Systems Lines (Auger Hoist)
AP555F Asphalt Paver Machine Systems Bypass Valve
2015/05/06 A New Clutch Wave Spring Is Now Used On Certain 14M and 16M Motor Graders {3063, 3155, 3170}
239D and 249D Compact Track Loaders and 226D and 232D Skid Steer Loaders Machine Systems Gas Spring - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Machine Systems Tilt Cylinder - Remove and Install - Single Tilt
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Machine Systems Tilt Cylinder - Remove and Install - Parallel Lift
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Machine Systems Lift Cylinder - Remove and Install - Single Tilt
735, 740 GC, 740 EJECTOR, 745 Articulated Trucks Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
MH3037 Material Handler Power Train Axle Housing - Remove and Install - Front Axle
MH3037 Material Handler Power Train Drive Shaft - Remove and Install - Front
MH3037 Material Handler Power Train Travel Motor - Remove and Install
AP655F and AP655F L Asphalt Paver Machine Systems Control Valve (Auxiliary)
AP655F and AP655F L Asphalt Pavers Propel System Lines (Track Tension)
AP655F and AP655F L Asphalt Paver Machine Systems Counterbalance Valve (Hopper Hoist, Tow Point)