PRODUCT SUPPORT PROGRAM FOR REPLACING THE GENERATOR TERMINAL STUDS ON CERTAIN C15 AND C18 GENERATOR SETS Caterpillar

PRODUCT SUPPORT PROGRAM FOR REPLACING THE GENERATOR TERMINAL STUDS ON CERTAIN C15 AND C18 GENERATOR SETS

Usage:

TEBE1680-00

Show/hide table

30Jun2014

U060
U170

Show/hide table

Before/After (Limited distribution)	PRODUCT SUPPORT PROGRAM FOR REPLACING THE GENERATOR TERMINAL STUDS ON CERTAIN C15 AND C18 GENERATOR SETS
4460		PS44390

Show/hide table

NOTE:

Caterpillar’s obligations under this Service Letter are subject to, and shall not apply in contravention of, the laws, rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction, without recourse or liability with respect to Caterpillar.

NOTE:

This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS44390" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.

Show/hide table

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table

TERMINATION DATE

30Jun2016

PROBLEM

Show/hide table

The generator terminal studs on certain C15 and C18 Generator Sets may break when the power leads are tightened.

AFFECTED PRODUCT

Show/hide table

Model	Identification Number
C15	L8B00179, 184-185, 187, 190-191, 193-194, 198, 200-201, 204-206, 214-219, 222-224, 235-240
C18	L8D00160, 168, 176, 183-184, 190-191, 195-199, 202-205

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
12	STUD	STUD (SEE ACTION REQUIRED)
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 32% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

Note: Dealers listed on this program should have already received the studs. If necessary, contact Jose Garnantini in regards to parts.

Email: GARGANTINI_JOSE_Sob@cat.com
Phone: +55 19 2106 1633

Important Safety Information

Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.

A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.

Safety precautions and warnings are provided in this instruction, on the product, and in this product's Operation and Maintenance Manual (OMM). If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.

Therefore, the warnings in this publication, the warnings that are on the product, and the warnings that are in the OMM are not all inclusive. If a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar is used, the user must ensure that it is safe for the user and for other people to use.

The user should ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.

WARNING: The generator set must be isolated electrically before and while the rework is performed. Follow the proper lockout tag out procedures to protect against the unexpected energizing or startup of the generator set. Failure to follow these warnings could result in injury to personnel during service. Attach a "Do Not Operate" warning tag to the machine start switch or the controls before you perform any service to the machine.

Refer to the attached Rework Procedure.

Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-20000 hrs, 0-60 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 1.0-hour job

Show/hide table

PARTS DISPOSITION

Show/hide table

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Rework Procedure

Show/hide table

Remove covers off the generator terminal box to gain access to the generator lead terminals.

Ensure all 12 generator lead cables are labeled and then disconnect each cable by removing the nut securing the cable by using a 3/4 inch socket as shown in Image 1.2.1.

Image1.2.1

Remove all 12 studs using an M6 hex wrench as shown in Image 1.3.1.

Image1.3.1

Install 12 new stud as shown in Image 1.4.1, tighten new M12 stud to 25 Nm +/- 3.5 Nm. Please note some studs may have a hex head and other may have a slotted head.

Reconnect all generator lead cables as per original generator lead configuration. The nut on the generator leads should be tightened to 35 Nm +/- 3.5 Nm