Gear Pump (Torque Converter Scavenge)
Show/hide table
Illustration 1 | g03890419 |
Show/hide table
Specification for 9P-9610 Gear Pump Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 1 | 8P-1812 Oil Pump Cover | - |
2 | 1 | 9G-7414 Oil Pump Body As | - |
3 | 1 | 117-1253 Oil Pump Manifold As | - |
4 | 2 | 3P-7898 Bushing | Bore of the bushings after installation (new) is |
5 | 2 | 126-4900 Bushing | Bore of the bushings after installation (new) is |
6 | 1 | 6I-9764 Shaft | Diameter of the shafts is |
7 | - | - | Clearance between the gears and the body (new) is |
8 | 1 | 9G-7411 Oil Pump Drive Gear | Diameter of the shafts is |
Show/hide table
Illustration 2 | g03890423 |
Show/hide table
Specification for 8P-1812 Oil Pump Cover | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 1 | 8P-1812 Oil Pump Cover | - |
9 | - | - | Depth of 3P-7898 Bushing into the cover is |
10 | - | - | Location of the 3P-7898 Bushing joint from the vertical centerline (as shown) is 30° ± 15°. |
Show/hide table
Illustration 3 | g03890424 |
Show/hide table
Specification for 9G-7414 Oil Pump Body As | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
2 | 1 | 9G-7414 Oil Pump Body As | - |
11 | 4 | 8M-8489 Dowel | Measurement from the end of the dowel to the face of the body is |
Show/hide table
Illustration 4 | g03890425 |
Show/hide table
Specification for 117-1253 Oil Pump Manifold As | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
3 | 1 | 117-1253 Oil Pump Manifold As | - |
12 | - | - | Location of the 126-4900 Bushing joint from the vertical centerline (as shown) is 30° ± 15° |
13 | - | - | Depth of the 126-4900 Bushing into the manifold is |
Caterpillar Information System:
R3000H Load Haul Dump Power Train Relief Valve (Torque Converter Outlet)
559C and 579C Knuckleboom Loaders Hydraulic Oil Contamination - Test
Procedure to Rework Hydraulic System on the AS4251C Asphalt Screeds {5050} Procedure to Rework Hydraulic System on the AS4251C Asphalt Screeds {5050}
CW14 Pneumatic CompactorEngine Supplement Alternator - Remove and Install
C175-16 and C175-20 Engines for Off-Highway Trucks Turbocharger
C13 Tier 4 Final Engines Engine Speed - Check
CB34B, CB34B XW, CB36B and CC34B Utility Compactors Belts - Inspect/Adjust/Replace
CB22B, CB24B, CB32B and CC24B Utility Compactors Water Tank Strainer - Clean and Inspect
CB34B, CB34B XW, CB36B and CC34B Utility Compactors Wheel Nuts - Tighten
CB22B, CB24B, CB32B and CC24B Utility Compactors Tire Inflation - Check
CB22B, CB24B, CB32B and CC24B Utility Compactors Towing the Machine
789D and 789D XQ Off-Highway Trucks Machine Systems Object Detection Box - Remove and Install
R3000H Load Haul Dump Braking System Pressure Switch (Parking Brake Oil)
988K XE Wheel Loader Systems Foot Brake Control
R3000H Load Haul Dump Steering System Pilot Valve (STIC Steering)
2012/10/16 The Service Wiring Group Has Been Updated on 777G Off-Highway Truck {1408, 7513}
C7.1 Industrial Engine Inlet Air Control - Remove - NRS Inlet Air Mixer
C7.1 Industrial Engine Inlet Air Control - Install - NRS Inlet Air Mixer
C7.1 Industrial Engine Fuel Injection Pump - Remove
C7.1 Industrial Engine Fuel Injection Pump - Install
C7.1 Industrial Engine Fuel Injection Pump Gear - Remove
C7.1 Industrial Engine Fuel Injection Pump Gear - Install
C7.1 Industrial Engine Electronic Unit Injector - Remove
C7.1 Industrial Engine Electronic Unit Injector - Install