Transmission (Power Shift) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 180-3034     | 一套修理台     | 4     |
B     | 8S-7615     | 触针     | 2     |
4C-6486 | 台架     | 2     | |
8S-7641 | 管     | 2     | |
8S-8048 | 鞍座     | 2     | |
C     | 208-5040     | 支持管     | 1     |
D     | 1U-7505     | 液压千斤顶     | 1     |
- 将工具 (D) 连接到变速箱组件 (18) 。 变速箱组件 (18) 的重量约为 255 kg (562 lb)。
Show/hide table
图 1 | g02918596 |
Show/hide table
图 2 | g02918480 |
- 使用工具 (D) 安装变速箱组件 (18) 。
- 将电缆带 (24) 从变矩器的驱动板 (25) 上拆下。
Show/hide table
图 3 | g02918506 |
- 旋转飞轮 (22) 以安装螺栓 (23) 。
Show/hide table
图 4 | g02918501 |
- 安装螺栓 (21) 。
Show/hide table
图 5 | g02918997 |
- 将安装件 (26) 安装到变速箱组件的每一侧上。 安装螺栓 (27) ,然后安装螺母和垫圈。
Show/hide table
图 6 | g02919002 |
- 安装盖 (20) 和螺栓 (19) 。
Show/hide table
图 7 | g02919018 |
- 安装变速箱机油滤清器。 请参考 操作和保养手册, "变速箱机油滤清器 - 更换"。
- 将软管 (17) 安装到液压油箱,然后安装卡箍 (16) 。 连接软管组件 (15) 。
Show/hide table
图 8 | g02918477 |
- 安装螺栓 (14) 、垫圈和螺母。 连接软管组件 (13) 。
Show/hide table
图 9 | g02918464 |
- 连接软管组件 (12) 。
Show/hide table
图 10 | g02918459 |
- 连接软管组件 (11) 。 安装软管 (10)
Show/hide table
图 11 | g02918418 |
- 将软管组件 (9) 连接至变速箱的右侧。
Show/hide table
图 12 | g02918400 |
- 连接线束组件 (8) 。
Show/hide table
图 13 | g02918359 |
- 连接线束组件 (1) 、 (2) 、 (3) 、 (4) 、 (5) 、 (6) 和 (7) 。
Show/hide table
图 14 | g01243334 |
- 安装后驱动轴。
- 如果适用,安装前驱动轴。
- 安装活塞泵。
- 使用工具 (D) 拆下工具 (A) 、工具 (B) 和工具 (C) 。 将机器降至地面上。
Show/hide table
图 15 | g01244146 |
Show/hide table
图 16 | g01244175 |
Show/hide table
图 17 | g01244145 |
- 变速箱里注油。 请参考操作和保养手册, "变速箱油 - 更换"。
- 断开可伸缩斗杆锁。 请参阅操作和保养手册, "可伸长斗杆锁定控制"。
- 断开回转动臂锁。 参考操作和保养手册, "回转锁销控制"。
- 断开动臂锁。 参考操作和保养手册, "动臂锁"。
Caterpillar Information System:
2012/03/21 A New Front Window Wiper Motor Group Is Now Used on 24M Motor Graders {7305}
553C, 563C and 573C Wheel Feller Bunchers Power Train Transmission Gearbox - Assemble
553C, 563C and 573C Wheel Feller Bunchers Power Train Transmission Gearbox - Disassemble
C2.6 and C3.3B Tier 2 and EU Stage 2 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust - C3.3B Engines
450E Backhoe Loader Power Train Transmission (Power Shift) - Remove
416F, 420F, 422F, 428F, 430F, 432F, 434F, 444F and 450F Backhoe Loaders Monitoring System Module - Replace
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Transmission (Direct Drive) - Install
Adjustment Procedure for Free Play in the Slide Frame of the Seat {7324} Adjustment Procedure for Free Play in the Slide Frame of the Seat {7324}
C2.6 and C3.3B Tier 2 and EU Stage 2 Engines for Caterpillar Built Machines Lubrication System
986H Wheel Loader Emerging Symptom Information
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Hydraulic Oil Contamination - Test
988K XE Wheel Loader System Pressure Release
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Gear Pump Flow (Steering) - Test
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Gear Pump Flow (Cooling Fan) - Test
C3.4B Engines Crankcase Breather Ejects Oil
2012/03/07 VIMSpc 2011A Update Utility Is Now Available for Certain CAT Products {7601}
C175-16 Locomotive Engine Electronic Service Tool Does Not Communicate
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Relief Valve (Steering) - Test
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Tire and Rim (Rear) - Remove and Install
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Transmission - Standard Shift
416F, 420F, 422F, 428F, 430F, 432F, 434F, 444F and 450F Backhoe Loaders Monitoring System Module - Configure
C175-16 Engines for Off-Highway Truck/Tractors Coolant Pressure Is Low
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Rear Axle - Remove
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Relief Valve (Charge) - Test and Adjust