Engine Oil Filter, Oil Filter Base and Oil Cooler - Remove and Install
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 185-3630 | 带式扳手组件 | 1 |
| B | - | LOCTITE 271 | 1 |
- 有关正确的排放和加注步骤，参考操作和保养手册, "发动机机油和滤清器 - 更换"。
Show/hide table
图 1 g02551841 - 使用工具 (A) 拆下机油滤清器 (1)。
- 断开软管组件 (2) 和适配器。 拆下机油滤清器底座 (3)。
Show/hide table
图 2 g02551876 - 拆下机油冷却器 (4)。
Show/hide table
图 3 g02551879 - 拆下盖 (9)。 拆下阀 (7)、适配器 (6) 和 O 形密封圈 (5)。
- 拆下螺塞 (8) 和 O 形密封圈。
Show/hide table
图 4 g02551939 Show/hide table
被弹簧力爆出的零件击中，会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序，并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (10)、O 形密封圈 (11)、弹簧 (12) 和阀 (13)。
Show/hide table
图 5 g02551944 - 拆下螺塞 (14) 和双头螺栓 (15)。
- 按与拆卸相反的顺序安装机油滤清器底座 (3) 和机油滤清器 (1)。
- 在双头螺栓 (15) 上涂抹 (X) 长的工具 (B)。 长度 (X) 为
10 ± 1.50 mm (0.40 ± 0.06 inch) 。 - 拧紧双头螺栓 (15) 至扭矩为
68 ± 7 N·m (50 ± 5 lb ft) 。 - 在机油滤清器 (1) 的密封件上涂抹清洁的发动机油。 手动拧紧，直到滤清器座合。 额外转动 3/4 圈。
Show/hide table
图 6 g02551958 - 在双头螺栓 (15) 上涂抹 (X) 长的工具 (B)。 长度 (X) 为
Caterpillar Information System:
924K, 930K, 938K, 950G II, 950H, 950K, 950L, 950M, 950M Z, 962G II, 962H, 962K, 962L, 962M, 962M Z, 966G II, 966H, 966K, 966L, 966M, 966M XE, 972G II, 972H, 972K, 972L, 972M, 972M XE, 980G II, 980H, 980K, 980L, 980M and 982M Wheel Loaders Automatic L Automatic Lubrication System - Test
797F and 797F XQ Off-Highway Truck Hydraulic Fan System System Pressure - Release
AP1055E Asphalt Paver Equipped with a Cat C6.6 Engine Declaration of Conformity
262C2 Skid Steer Loader, 277C2 and 287C2 Multi Terrain Loaders and 279C2 and 289C2 Compact Track Loaders Operator Controls
C4.4 Engines For Caterpillar Built Machines Starting Aid (Glow Plug) Relay Circuit - Test
PL83 and PL87 Pipelayers Declaration of Conformity
C4.4 Engines For Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
C4.4 Engines For Caterpillar Built Machines Engine Wiring Information
C4.4 Engines For Caterpillar Built Machines CID 0168 FMI 00
C4.4 Engines For Caterpillar Built Machines CID 0004 FMI 06
C4.4 Engines For Caterpillar Built Machines CID 0004 FMI 05
C4.4 Engines For Caterpillar Built Machines CID 0003 FMI 06
3516B Engine for 994F and 994H Wheel Loaders Diagnostic Trouble Codes
Tier II Level Emissions Engine Repower for a 777D Off-Highway Truck {1000} Tier II Level Emissions Engine Repower for a 777D Off-Highway Truck {1000}
Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383} Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383}
C9.3 Engines for Caterpillar Built Machines Power Train Oil Cooler - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Event Codes
262C2 Skid Steer Loader, 277C2 and 287C2 Multi Terrain Loaders and 279C2 and 289C2 Compact Track Loaders Caterpillar Approved Work Tools
Bench Test Procedure for a 24M Motor Grader Transmission{3030, 3073, 3139} Bench Test Procedure for a 24M Motor Grader Transmission{3030, 3073, 3139}
986H Wheel Loader Machine Systems Speed Sensor (Transmission Output)
SC-57 Felling Head Felling Head General Information
2011/05/26 Fuel Filter Has Changed on Certain Multi Terrain Loaders, Skid Steer Loaders, and Compact Track Loaders {1258, 1261, 1263}
2011/05/16 Improved Messenger Software is Now Available on Certain 770 and 772 Off Highway Trucks {7620}
Adapting 140M and 160M Snow Wings to 140M Series 2 and 160M Series 2 Motor Graders{6158, 6159} Adapting 140M and 160M Snow Wings to 140M Series 2 and 160M Series 2 Motor Graders{6158, 6159}