Engine Starting with Auxiliary Start Receptacle
Show/hide table
注意 |
---|
为了防止发动机轴承和电路受到损害,在跨接起动机器时,不要让待起动机器接触到用作电源的机器。 连接跨接线之前,接通(闭合)蓄电池断路开关,以免损坏待起动机器上的电气元件。 起动只允许使用相同电压。 检查机器的蓄电池和起动机的额定电压。 跨接启动时,只能用相同的电压。 使用电焊机或较高的电压会损坏电气系统。 跨接起动后,交流发电机无法将严重放电的免维护蓄电池充满电。 必须用蓄电池充电器来将蓄电池充电至正确的电压。 许多被认为是无法使用的蓄电池实际上仍可充电。 请参考专门说明书, SEHS7633, "蓄电池测试步骤"中完整的测试和充电信息。 本出版物可从您的 Cat 代理商处获得。 |
一些机型可能把辅助起动插座作为机器的标准配置提供。 其他所有机器也可通过零件服务来配备这样的插座。 这样,机器上就有永久式插座作为跨接起动用途。
还提供两组电缆总成,以便通过其它也配备了插座或辅助电源组的机器对停运机器进行跨接起动。 您的 Cat 代理商可为您的具体应用提供正确的电缆。
- 进行初步判断,确定机器无法起动。
- 把停运机器上的变速箱移动至停止位置。 接合停车制动器。 将所有附件降至地面上。
- 在停运机器上,将发动机起动开关转到断开位置。 关闭所有附件。
- 接通停运机器上的蓄电池断路开关。
- 将用作电源的机器移近,以使其能将跨接电缆连接到停运机器上。 但决不允许两台机器互相接触。
- 将用作电源的机器的发动机熄火。 如果使用了辅助电源,则关闭充电系统。
Show/hide table
图 1 g02475821 辅助起动插座 - 在停运机器上,将相应的跨接起动电缆连接到辅助起动插座上。
- 将跨接起动电缆的另一端连接到电源的辅助起动插座上。
- 起动用作动力源机器上的发动机。 如果使用了辅助电源,将辅助电源的充电系统通电。
- 等待至少两分钟,让待起动机器的蓄电池能部分充电。
- 试着起动待起动发动机。 请参阅操作和保养手册, "发动机起动"。
- 在起动了待起动发动机后立即将跨接起动电缆从用作电源的机器上断开。
- 将跨接起动电缆的另一端从待起动机器上断开。
- 在发动机运转且充电系统工作正常后,根据需要,完成对停运机器的起动充电系统进行的故障分析。
Caterpillar Information System:
541 Series 2 and 552 Series 2 Track Feller Bunchers Safety Messages
AP500F Asphalt Paver Engine Starting with Jump Start Cables
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Screed Adjustment
2011/03/22 The Proper Procedure to Enter Claims in SIMSi for Plugged /Restricted Fuel Filters and Water Separators on Certain Engines {1260, 1261, 1262, 1263}
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Power Train Pressures
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Soot Antenna - Remove and Install
584 and 584HD Forwarders Power Train Articulating and Oscillating Hitch
Comfort Series Seat For Caterpillar Machines Optimized Seat Air Suspension with Air Compressor
2011/05/09 Additional Front Signal Lamps Are in Production on Certain Off-Highway Trucks {1430, 1432}
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Seat
AP1055E and BG1055E Asphalt Pavers Machine Systems Position Sensor (Paddle)
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Fan Drive System - Test
2011/07/01 Improvements to the Drive Motor Group on Certain Skid Steer Loaders {5058}
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Clean Emissions Module - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Specifications
AP1000E and BG1000E Asphalt Pavers Machine Systems Screed - Remove and Install
AP1055E and BG1055E Asphalt Pavers Propel System Track Roller Frame (Mobil-Trac)
2011/03/18 Revised Piston Cooling Jets - Remove and Install for C175-16 and C175-20 Machine Engines {1214}
Rework Procedure For Brake Friction Discs, Brake Control Valves, and the Covers on Certain M Series Motor Graders{4251, 4265, 4267, 4269} Rework Procedure For Brake Friction Discs, Brake Control Valves, and the Covers on Certain M Series Motor Graders{4251, 4265, 4267, 4269}
541 Series 2 and 552 Series 2 Track Feller Bunchers Daily Inspection
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Ventilation Blower Wheel - Inspect/Clean
541 Series 2 and 552 Series 2 Track Feller Bunchers Alternate Exit
AP1055E and BG1055E Asphalt Pavers Machine Systems Final Drive Planetary - Remove
AP1055E and BG1055E Asphalt Pavers Machine Systems Final Drive Planetary - Install