Relief Valve (Hoist Raise, Hoist Lower) - Test and Adjust
Show/hide table
所需工具     | ||
---|---|---|
零件号     | 说明     | 所需数量     |
6V-3079     | 压力软管组件     | 1     |
6V-4143     | 连接器组件     | 2     |
198-4240     | 数字压力指示器     | 1     |
注: 在您进行任何压力测试之前,确保滤清器和滤网清洁。 在您进行本测试之前,确保油处于工作温度。
注: 执行任何测试前,目视检查整个液压系统有无漏油和部件损坏。
Show/hide table
机器突然移动,会造成人员伤亡。 突然移动车辆或释放油压会伤害车上或附近的人员。 为了防止受伤,测试和调整液压系统前,执行测试和调整, "概述"部分内的程序。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
图 1 | g01258000 |
(1) 高压安全阀 (2) 低压安全阀 (3) 举倾机构双级安全阀 (4) 举倾机构控制阀 |
举倾两级安全阀 (3) 是举倾控制阀 (4) 的一部分。 上升位置的卸压压力由高压安全阀 (1) 控制。 降下位置的卸压压力由低压安全阀 (2) 控制。
安全阀测试(高压)
Show/hide table
图 2 | g02422536 |
(5) 高压机油测压口 |
- 降下卸载车斗。 关闭发动机。
- 将软管组件及 8T-0860 压力表 (0 到 40000 kPa (0 到 5800 psi)) 连接到测压口 (5) 。
- 起动发动机。 反复操作卸载车斗,直到液压油温度超过 38°C (100°F) 为止。
- 高怠速运行发动机,并将举倾操纵杆移到升起位置。
- 卸载车斗完全升起后查看压力表。 将举倾操纵杆保持在升起位置。 高压表读数便是高压安全阀 (1) 的安全阀压力设定值。 775G 机器正确的压力设定值为 18950 + 1000 - 500 kPa (2750 + 145 - 73 psi)。
- 松开螺母 (6) 。 通过转动护圈 (7) 调整高压安全阀 (1) 的设定值。
Show/hide table
图 3 | g00531382 |
(1) 高压安全阀 (2) 低压安全阀 (3) 举倾机构双级安全阀 (6) 螺母 (7) 保持器 |
- 高压安全阀 (1) 正确设定后,拧紧螺母 (6) 。
安全阀测试(低压)
Show/hide table
图 4 | g02422556 |
(8) 低压机油测压口 |
- 降下卸载车斗。 关闭发动机。
- 将软管组件及 8T-0856 压力表 (0 到 6000 kPa (0 到 870 psi)) 连接到测压口 (8) 。
- 起动发动机。 反复操作卸载车斗,直到液压油温度超过 38°C (100°F) 为止。
- 将卸载车斗降到卡车车架上。
注: 车斗降下或上升开关必须处于上升位置才能测量低压安全阀 (2) 。 如果车斗降下或上升开关处于降下位置,则动力传动系电子控制模块将使举倾控制阀始终处于 SNUB 位置。 不能在这种情况下测量低压安全阀 (2) 。
- 将磁铁从车斗上拆下。 当磁铁拆下切车斗位于降下位置时,仪表板上的指示灯发光。
- 高怠速运行发动机,并将举倾操纵杆移到降下位置。
- 将举倾操纵杆保持在降下位置的同时观察压力表。 低压表读数便是低压安全阀 (2) 的安全阀压力设定值。 正确的压力设定值为 3450 ± 350 kPa (500 ± 50 psi)。
- 松开螺母 (10) 。 通过转动护圈 (9) 调整低压安全阀 (2) 的设定值。
Show/hide table
图 5 | g00531539 |
(1) 高压安全阀 (2) 低压安全阀 (3) 举倾机构双级安全阀 (9) 保持器 (10) 螺母 |
- 低压安全阀 (2) 正确设定后,拧紧螺母 (10) 。
Caterpillar Information System:
770G and 772G Off-Highway Truck Systems Hoist Control - Adjust
770G and 772G Off-Highway Truck Systems Brake System Air - Purge
770G and 772G Off-Highway Truck Systems Brake Cooling Pressure - Check
770G and 772G Off-Highway Truck Systems Gear Pump (Brake, Brake Cooling, Hoist) - Purge
770G and 772G Off-Highway Truck Systems Slack Adjuster - Test and Adjust
770G and 772G Off-Highway Truck Systems Secondary Brake System Pressure Test
770G and 772G Off-Highway Truck Systems Service Brakes and Retarder System Pressure - Test
770G and 772G Off-Highway Truck Systems Service Brake Discs - Check
770G and 772G Off-Highway Truck (OEM) Hydraulic and Braking System Brake Oil Overheating Troubleshooting
770G and 772G Off-Highway Truck (OEM) Hydraulic and Braking System Hoist System Troubleshooting
770G and 772G Off-Highway Truck (OEM) Hydraulic and Braking System Limit Switch (Truck Body Up)
770G and 772G Off-Highway Truck (OEM) Hydraulic and Braking System Brake Valve (Rear Service Brake, Retarder Control, Traction Control)
770G and 772G Off-Highway Truck Systems Relief Valve (Brake Oil Cooler) - Test and Adjust
M320D2 Wheeled Excavator Machine System Specifications Axle Oscillation Lock Cylinder
M316C Excavator Machine System Universal Joints
770G and 772G Off-Highway Truck Power Train Transmission Pressures - Test and Adjust
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Relief Valve (Charge) - Test and Adjust
2013/04/05 A New Rework Procedure Improves Steering and Implement Pump on Certain M Series Motor Graders {5070}
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Relief Valve (Main) - Test - Drag Conveyor and Auger Conveyor
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Piston Pump (Auger Conveyor and Drag Conveyor) Neutral - Test and Adjust
Installation of Cat® Detect Object Detection for the 777D Off-Highway Truck/Tractor {1408, 7348} Installation of Cat® Detect Object Detection for the 777D Off-Highway Truck/Tractor {1408, 7348}
Installation of Cat® Detect Object Detection for the 24H Motor Grader {1408, 7348} Installation of Cat® Detect Object Detection for the 24H Motor Grader {1408, 7348}
2011/02/21 An Optional Rework Procedure Is Now Available for the Window Wiper Park Position on Certain Series M Motor Graders {7305}
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Piston Pump (Conveyor)