Axle (Steering Positive Stop) - Test and Adjust
简介
此步骤用于调整轮轴转向接头组件的转向轴止动块。 轮轴壳体带有一个凸起,凸起上的接触面经过处理,可限制转向节的旋转。
所需工具
Show/hide table
所需工具     | |||
---|---|---|---|
项目     | 数量     | 零件号     | 说明     |
F1     | 1     |     | 量角器     |
F2     | 1     | FT-2294     | 定位杆     |
F3     | 1     |     | 方形     |
    | 1     | FT-2295     | 扳手 ( 75 mm)     |
    | 1     | FT-2296     | 扳手 ( 41 mm)     |
    | 1     |     | 卡尺     |
机器准备
- 使所有人员远离机器和机器周围。
- 起动发动机。
- 将发动机转速刻度盘设置在位置 "10"。
Show/hide table
图 1 | g02449876 |
发动机转速旋钮 |
- 降下左侧操纵台。
- 将机器停放在水平地面上。 检查视野并调整反光镜,使机器附近的视野达到最佳。
- 完全踩下行车制动器踏板,直到行车制动器踏板机械式锁定。
- 降下稳定器和铲刀尖。
- 完全伸出铲斗油缸,然后将铲斗置于地面上。
- 停止发动机。
- 释放液压系统压力。
注: 请参阅测试和调整, "系统压力 - 释放".
- 举升左操纵台。
测试步骤
- 转动方向盘直到方向盘不再转动。 向右转动方向盘以便检查右轮。 向左转动方向盘以便检查左轮。
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
Show/hide table
图 2 | g02416939 |
转向锁 (F1) 量角器 (F2) FT-2294 定位杆 (F3) 方形 (1) 毂表面 |
- 将方形 (F3) 置于毂表面 (1) 上。 使用量角器 (F2) 测量方形 (F3) 与定位杆 (3) 之间的角度。 该角度应为 35 度。
注: 该角度与内侧车轮相关。 外侧车轮的角度为 28 度(标准轮胎)。
调整步骤:
- 松开调整螺栓 (2) 上的锁紧螺母。 转动调整螺栓 (2) 直到达到正确的角度。
Show/hide table
图 3 | g02416940 |
(A) 35 度 (B) 28 度 (2) 调整螺栓 |
- 将调整螺栓 (2) 上的锁紧螺母拧紧至规定扭矩。
- 卸下工具。
- 对另一侧的车轮重复此步骤。
Caterpillar Information System:
770G and 772G OEM Off-Highway Truck General Information
2011/02/08 New Product Link Cellular Is Released for All Cat Products {7606}
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Seat - Remove and Install
770G and 772G OEM Off-Highway Truck Power Train Hydraulic System
770G and 772G OEM Off-Highway Truck Power Train Hydraulic System
770G and 772G Off-Highway Truck (OEM) Hydraulic and Braking System Hydraulic System
583T Pipelayer Hydraulic System Hydraulic Tank and Filter
Cat® Grade Control Cross Slope for Motor Graders Full Sensor - Calibrate
770G and 772G OEM Off-Highway Truck Power Train Electrical System
980M Tier 4 and 982M Tier 4 Wheel Loaders Hood Tilt Cylinder - Remove and Install
770G and 772G OEM Off-Highway Truck Final Drive
C15 and C18 Petroleum Generator Sets Engine Valve Lash - Check
Cat® Grade Control Cross Slope for Motor Graders Bank Valve (Grade Control) - Calibrate
Disassembly and Assembly Procedures for Track Rollers with Inverted Duo-Cone Seals {0599, 0729, 4180, 4180, 7555, 7561} Disassembly and Assembly Procedures for Track Rollers with Inverted Duo-Cone Seals {0599, 0729, 4180, 4180, 7555, 7561}
C7.1 Engines For Caterpillar Built Machines Glossary
C7.1 Engines For Caterpillar Built Machines Indicator Lamps
AS4252C Asphalt Screed Screed Cleanup
AP1055E and BG1055E Asphalt Pavers Engine Supplement Expansion Tank - Remove and Install
Cat® Grade Control Cross Slope for Motor Graders Sensor - Adjust - Blade Slope Sensor
Cat® Grade Control Cross Slope for Motor Graders Sensor - Adjust - Mainfall Sensor
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Left Propel) - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Left Propel) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Drive - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Drive - Install