Exhaust Elbow - Remove and Install
Removal Procedure
- If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
- Loosen clamp assemblies (1) , (3) and (5) .
Note: Mark the orientation of clamp assembly (3) prior to removal.
Show/hide table
Illustration 1 | g02331933 |
- Slide elbow (2) into bellows (4) in order to gain clearance. Remove the bellows assembly.
Installation Procedure
- If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
- Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (2) . a Distance (X) from the end of elbow (2) .
Show/hide table
Illustration 2 | g02095400 |
Show/hide table
Illustration 3 | g02332313 |
Alignment wrap (A) is not shown for photographic purposes. Typical Example |
Note: Alignment wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.
Note: The alignment wrap (A) should not be removed until Step 11. Bellows (4) should never be flexed during installation.
- Insert elbow (2) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.
- Prior to installation, position both ball clamp assemblies (1) and (5) onto the bellows assembly.
Show/hide table
Illustration 4 | g02331933 |
Alignment wrap (A) is not shown for photographic purposes. |
Show/hide table
Illustration 5 | g02097701 |
The photo is a cutaway view of the ball clamp assembly which is located near the combustion head group. |
Show/hide table
Illustration 6 | g02098533 |
The photo is a cutaway view of the ball clamp assembly. |
- Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (2) in the slip joint at clamp assembly (3) in order to position the bellows assembly.
- Verify that the cup of the ball joint (E) does not touch the radius of the ball (D) . Position ball clamp (1) and hand tighten ball clamp (1) . Measure Distance (Y) and Distance (Z) . The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1) . If necessary, adjust ball clamp (1) .
- Repeat Step 6 for ball clamp (5) which is located near the turbocharger.
- Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (3) .
- Torque ball clamp (1) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).
Note: Do not use power tools in order to torque clamp assemblies (1) , (3) , and (5) .
- Torque ball clamp (5) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).
- Remove alignment wrap (A) from bellows (4) .
- Torque clamp assembly (3) to a torque of 55 ± 8 N·m (41 ± 6 lb ft).
Caterpillar Information System:
770G and 772G Off-Highway Truck Oil Cooler (Hydraulic Fan, Steering) - Remove and Install
770G and 772G Off-Highway Truck Engine Lockout Control
C15 and C18 Tier 4 Final Engines Electronic Unit Injector - Adjust
2010/12/14 The Hydraulic Oil Lines Group has Been Improved on the 777F Off-Highway Truck {5057}
Bench Test Procedure for a D6T and D6R Track-Type Tractor and PL72 Pipelayer Transmission{3030, 3073} Bench Test Procedure for a D6T and D6R Track-Type Tractor and PL72 Pipelayer Transmission{3030, 3073}
120M Series 2, 120M2, 12M Series 2, 12M Series II, 140M Series 2 and 160M Series 2 Motor Graders Implement Electronic Control System MID 145 - CID 1473 - FMI 12
120M Series 2, 120M2, 12M Series 2, 12M Series II, 140M Series 2 and 160M Series 2 Motor Graders Implement Electronic Control System MID 145 - CID 1472 - FMI 12
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Supplement Engine - Remove and Install
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train Electronic Control System MID 027 - CID 0297 - FMI 14
C4.4 Industrial Engine Clean Emissions Module
320E and 323E Excavators Machine System Specifications Control Valve (Auxiliary)
320E and 323E Excavators Machine System Specifications Relief Valve (Line)
2010/12/09 A New Swing Cylinder Provides Improved Durability and Reliability on Certain Backhoe Loader Machines {7562}
770G and 772G Off-Highway Truck Machine Lockout Control
773G and 775G Off-Highway Truck Hydraulic and Braking System Operational Checks
777G Off-Highway Truck Hydraulic and Braking System Hoist System Troubleshooting
Overflow Guard Installation Procedure for Certain Buckets on R1600G and R1600H Load Haul Dump Machines{7186, 7186} Overflow Guard Installation Procedure for Certain Buckets on R1600G and R1600H Load Haul Dump Machines{7186, 7186}
C13 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install
777G Off-Highway Truck Hydraulic and Braking System Brake System Troubleshooting
C13 Engines for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
770G and 772G Off-Highway Truck Electric Drive Pump (Prelubrication) - Remove and Install
777G Off-Highway Truck Hydraulic and Braking System Brake Oil Overheating Troubleshooting
Installation Procedure for Coolant Level Sensor Retrofit for Non-VIMS 777F Machines{7422} Installation Procedure for Coolant Level Sensor Retrofit for Non-VIMS 777F Machines{7422}
2011/01/10 New Liquid Level Sensor Group Is Now Available on 777F Non-VIMS Off-Highway Trucks {7422}