After Stopping Engine
注: 检查发动机机油之前，停止运行发动机至少 10 分钟以便使发动机机油回到油底壳。
Show/hide table
 |
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南，可能会造成人身伤亡。 |
- 发动机停机后，在对发动机的燃油管进行任何维修或修理之前，必须等待 10 分钟以便释放高压燃油管中的燃油压力。 如有必要，进行小的调整。 修理低压燃油系统以及冷却、润滑或空气系统中的所有泄漏。 更换存在泄漏的所有高压燃油管。 请参考拆解和组装手册, "燃油喷油管 - 安装"。
- 检查曲轴箱机油油位。 保持机油油位在发动机机油油尺的"最小"标记与"最大"标记之间。
- 如果发动机配备一个工时计，记录其读数。 按本操作和保养手册, "保养周期表"所述进行保养。
- 加满燃油箱以便于防止燃油中积聚湿气。 燃油箱不要加油过满。
Show/hide table
| 注意 |
|---|
在本操作和保养手册中的加注容量和建议标题下只能使用推荐的防冻剂/冷却液混合液。不这样做会造成发动机损坏。 |
Show/hide table
|
加压的系统： 热的冷却液能造成严重的烫伤。 在发动机停机，等待冷却系统部件冷却下来后再打开冷却系统加注口盖。 缓慢松开冷却系统加注口盖，以释放掉所有压力。 |
- 让发动机冷却。 检查冷却液液位。
- 检查冷却液有无正确的防冻保护和防腐保护。 如有必要，添加正确的冷却液/水混合液。
- 对所有从动设备进行必需的定期保养。 此保养会在 OEM 的使用说明书中述及。
Caterpillar Information System:
C4.4 Industrial Engine Before Starting Engine
793F Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet, Torque Converter Outlet) - Assemble
CD54 Paving Compactor Steering Wheel Encoder - Test
793F Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet, Torque Converter Outlet) - Disassemble
2009/09/30 A New Front Suspension Frame Bearing Is Now Used {7050, 7203}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems Location of Electrical Components
793F Off-Highway Truck Power Train Relief Valve (Torque Converter Outlet) - Remove and Install
793F Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
12M Motor Grader Caterpillar Approved Work Tools
793F Off-Highway Truck Power Train Torque Converter - Remove and Install
C4.4 Industrial Engine Engine Stopping
793D Off-Highway Truck Engine Supplement Engine and Torque Converter - Remove and Install
C4.4 Industrial Engine System Pressure Release
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector - Test
Procedure to Install a Track Guide on the Front and Center Bogies on Certain AP655D Asphalt Pavers{4192} Procedure to Install a Track Guide on the Front and Center Bogies on Certain AP655D Asphalt Pavers{4192}
Procedure for Filtering Off-Highway Truck Hydraulic Oil{0680, 0738, 0768, 5050, 5056} Procedure for Filtering Off-Highway Truck Hydraulic Oil{0680, 0738, 0768, 5050, 5056}
793F Off-Highway Truck Power Train Flow Control and Relief Valve (Rear Axle Oil) - Remove and Install
A Procedure to Replace the Relief Valve on the Hydraulic Generator for Certain AP655D Asphalt Pavers{4450, 5070, 5117} A Procedure to Replace the Relief Valve on the Hydraulic Generator for Certain AP655D Asphalt Pavers{4450, 5070, 5117}
2009/08/10 An Improved Adjustment Procedure for the Stop Lamp Switch is Now Available {1435, 4269}
Installation Instructions for Abrasion Sleeves and Edge Trim{1408, 5057, 7150, 7167} Installation Instructions for Abrasion Sleeves and Edge Trim{1408, 5057, 7150, 7167}
795F AC and 795F AC XQ Off-Highway Truck Power Train Electronic Control System Electrical Input Components
CD54 Paving Compactor Speed Sensor (Left Front Drum) - Test
CD54 Paving Compactor Speed Sensor (Left Rear Drum) - Test
CD54 Paving Compactor Speed Sensor (Right Front Drum) - Test