Generator - Remove and Install - 35K
Start By:
- Remove the piston motor (hydraulic generator). Refer to Disassembly and Assembly, "Piston Motor (Hydraulic Generator) - Remove".
- Remove clamp (2) from hose assemblies (1).
Show/hide table
Illustration 2 g01536675 - Remove the bolts and cover (3).
Show/hide table
Illustration 3 g01536676 - Remove the bolts and cover (4).
Show/hide table
Illustration 4 g01536677 - Remove the bolts and cover (7).
- Remove bolt (6) and pin (5).
Show/hide table
Illustration 5 g01536678 - Remove clamp (8) from harness assembly (9).
Show/hide table
Illustration 6 g01536679 - Remove bolts (10) that hold breaker panel (11) to generator (12). Move breaker panel (11) out of the way.
Show/hide table
Illustration 7 g01536680 - Remove the bolt and move ground cable (13) out of the way.
Show/hide table
Illustration 8 g01536681 - Remove the bolts and move panel (14) out of the way.
Show/hide table
Illustration 9 g01536683 Show/hide tableIllustration 10 g01536684 - Attach a suitable lifting device to generator (12). Remove bolts (15) and remove generator (12) from the machine. The weight of generator (12) is approximately
220 kg (485 lb) .
Show/hide table
Illustration 1 | g01536674 |
- Attach a suitable lifting device to generator (12). Install generator (12) and bolts (15). The weight of generator (12) is approximately
220 kg (485 lb) .Show/hide tableIllustration 13 g01536681 - Reposition panel (14) and install the bolts.
Show/hide table
Illustration 14 g01536680 - Reposition ground cable (13) and install the bolt.
Show/hide table
Illustration 15 g01536679 - Reposition breaker panel (11) on generator (12) and install bolts (10).
Show/hide table
Illustration 16 g01536678 - Install clamp (8) to harness assembly (9).
Show/hide table
Illustration 17 g01536677 - Install pin (5) and bolt (6).
- Install cover (7) and the bolts.
Show/hide table
Illustration 18 g01536676 - Install cover (4) and the bolts.
Show/hide table
Illustration 19 g01536675 - Install cover (3) and the bolts.
Show/hide table
Illustration 20 g01536674 - Install clamp (2) to hose assemblies (1).
Show/hide table
Illustration 11 | g01536683 |
Show/hide table
Illustration 12 | g01536684 |
End By:
- Install the piston motor (hydraulic generator). Refer to Disassembly and Assembly, "Piston Motor (Hydraulic Generator) - Install".
Caterpillar Information System:
2008/06/30 A New Kit for the Fuel Transfer Pump is Now Used {1256, 1714}
AP655D Asphalt Paver Machine Systems Piston Motor (Hydraulic Generator) - Install - 35K
AP655D Asphalt Paver Machine Systems Piston Motor (Hydraulic Generator) - Remove - 35K
795F AC and 795F AC XQ Off-Highway Truck Hydraulic System and Brakes Diverter Valve (Brake Cooling)
422E and 428E Backhoe Loaders Stabilizer Control
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Assemble
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders Machine Systems Ride Control Accumulator
PL61 Pipelayer Power Train Systems Equalizer Bar
C9.3 Engine for Caterpillar Built Machines Fuel Injection Pump
795F AC and 795F AC XQ Off-Highway Truck Hydraulic System and Brakes Cab Mounting
CB-534D, CB-534D XW and CB-564D Paving Compactors Machine Systems Position Switch (Offset) - Check and Adjust
422E and 428E Backhoe Loaders Swing Frame and Cylinder Bearings - Lubricate/Inspect
416E, 422E and 428E Backhoe Loaders Engine Crankcase Breather - Replace
Installation of Pivot Kit For Steering Columns{4310, 4338} Installation of Pivot Kit For Steering Columns{4310, 4338}
2008/05/26 Improved Accessory Drives for the PTO are Used {1207}
795F AC and 795F AC XQ Off-Highway Truck Hydraulic System and Brakes Gear Pump (Brake Cooling)
2008/10/13 New Inspection Procedure for the Antenna of the TC900B and TC900C Radios {733T}
AP600D Asphalt Paver Propel System Relief Valve (Charge) - Test and Adjust
An Air Dryer is Available for the Air Compressor and the Governor Assembly {1803, 4285} An Air Dryer is Available for the Air Compressor and the Governor Assembly {1803, 4285}
795F AC and 795F AC XQ Off-Highway Truck Hydraulic System and Brakes Gear Pump (Brake)
Procedure for Inspecting the Antenna of the TC900B and TC900C Radios{733T} Procedure for Inspecting the Antenna of the TC900B and TC900C Radios{733T}
785D Off-Highway Truck Frame - Clean/Inspect
785D Off-Highway Truck Frame and Body - Inspect
785D Off-Highway Truck Frame and Body Support Pads - Clean/Inspect