Track - Connect
Connection Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Description | Qty |
| A | 5P-2379 | Press Frame | 1 |
| 8S-7172 | Hydraulic Cylinder | 1 | |
| 8S-9903 | Track Press Rollover Gp | 1 | |
| 3S-6224 | Electric Hydraulic Pump Gp | 1 | |
| B | 1P-3532 | Track Block Assembly | 1 |
| C | 5P-0960 | Molybdenum Grease | 1 |
- Attach a suitable lifting device in order to raise the track onto Tooling (B). Raise the track until the two pin bores in the track links are in alignment with each other. Apply Tooling (C) in the master pin bores in the track assembly and on the master pin. Use Tooling (A) in order to install the master link. Install the master link pin until the protrusion of the pin is equal on both sides.
Show/hide table
 | |
| Illustration 1 | g01442557 |
- Install pads (3) and bolts (2) .
Show/hide table
 | |
| Illustration 2 | g01441777 |
- Tighten plug (1). Refer to Testing and Adjusting Manual in order to adjust the track tension.
Show/hide table
 | |
| Illustration 3 | g01441778 |
Caterpillar Information System:
PM-201 Cold Planer Machine Systems Track - Separate
24M Motor Grader Machine Systems Bottom Guard - Remove and Install
3508B Engine for Caterpillar Built Machines Crankcase Breather
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Engine Speed/Timing Sensor
2008/12/15 Correction to Systems Operation , "Power Train Electronic Control System" {4800, 7610}
2007/12/24 An Improved Pump Control Valve Is Available for the High Flow Work Tool Pump on Certain Multi Terrain Loaders and Skid Steer Loaders {5070, 5455}
2008/02/04 Correction to Systems Operation , "Power Train Electronic Control System" {4800, 7610}
R1700G Load Haul Dump Before Starting Engine
2007/12/17 A New Lens is Available for the Rear Tail Lamp {1429, 1434}
450E Backhoe Loader Hydraulic and Steering System Multipurpose Bucket Cylinder
24M Motor Grader Engine Supplement Muffler - Remove and Install
2010/10/13 Four Bearings Are Now Used On the Hydraulic Control Support (Armrest) {5258}
450E Backhoe Loader Diagnostic Code List
C4.4 and C6.6 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Wiring Information
450E Backhoe Loader MID 039 - CID 0041 - FMI 03
C175-16 Locomotive Engine Electric Starting Motor
450E Backhoe Loader MID 039 - CID 0041 - FMI 04
PM-201 Cold Planer Machine Systems Conveyor Idler (Second Stage) - Remove and Install
2008/05/12 An Improved Pinion Shaft with a New Rugged Bolted Joint Provides Consistent Torque on the Circle Drive {5207}
2008/05/12 An Improved Pinion Shaft with a New Rugged Bolted Joint Provides Consistent Torque on the Circle Drive {5207}
Topcon® System Five Safety Messages
247B2 and 257B2 Multi Terrain Loaders Machine Systems Undercarriage - Right Hand
247B2 and 257B2 Multi Terrain Loaders Machine Systems Undercarriage - Left Hand