Bank Valve - Install - Rear Frame
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 311-1362 | Vacuum Cap | 1 |
| B | 138-7575 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) and a suitable lifting device in order to install bank valve (14). The weight of bank valve (14) is approximately
73 kg (160 lb) .Show/hide table
Illustration 2 g01429188 Show/hide table
Illustration 3 g01429190 - Install bolts (13).
Show/hide table
Illustration 4 g01429187 - Position harness assembly (10) to support (12). Install bolts (11). Connect harness assembly (10).
Show/hide table
Illustration 5 g01429174 - Connect harness assemblies (7). Repeat this Step for the opposite side of the machine.
- Connect tube assemblies (8) and (9).
Show/hide table
Illustration 6 g01429008 - Connect tube assembly (6).
- Connect hose assemblies (4).
- Install tube assemblies (3) and (5).
- Repeat Steps 6 through 8 for the opposite side of the machine.
Show/hide table
Illustration 7 g01429013 - Position cover (2) and install bolts (1). Repeat this Step for the opposite side of the machine.
Show/hide table
Illustration 8 g01392655 - Remove Tooling (A).
- Fill the hydraulic tank. Refer to Operation and Maintenance Manual, "Capacities - Refill".
Show/hide table
| |
| Illustration 1 | g01429319 |
Caterpillar Information System:
785D OEM Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
PM-201 Cold Planer Machine Systems Service Support - Remove and Install
PM-201 Cold Planer Machine Systems Steering Linkage - Remove and Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Differential and Bevel Gear (Center) - Assemble
725, 730 and 730 EJECTOR Articulated Trucks Power Train Differential and Bevel Gear (Center) - Disassemble
725, 730 and 730 EJECTOR Articulated Trucks Power Train Differential and Bevel Gear (Front and Rear) - Assemble
725, 730 and 730 EJECTOR Articulated Trucks Power Train Differential and Bevel Gear (Front and Rear) - Disassemble
2007/11/26 An Orifice in the Brake Line Improves the Performance of the Parking Brake Switch {1408, 4257, 4267}
2007/11/12 Correction to Operation and Maintenance Manuals for the E Series Backhoe Loaders {7300, 7451}
450E Backhoe Loader Hydraulic and Steering System Control Valve (Extendable Stick) (Pilot Operated)
785D OEM Off-Highway Truck Drive Shaft Slip Joint - Lubricate
AS2252C Asphalt Screed Power Adjuster Motor (Height)
785D OEM Off-Highway Truck Engine Air Filter Service Indicator - Inspect
AP655D Asphalt Paver Propel System Location of Electrical Components (Propel System)
3516B Engine for 994F and 994H Wheel Loaders Fuel Consumption Is Excessive
Procedure for Troubleshooting and Cleaning the Oil Rail System for the Hydraulic Electronic Unit Injector (HEUI) {1100, 1126, 1250, 1251, 1261, 1290} Procedure for Troubleshooting and Cleaning the Oil Rail System for the Hydraulic Electronic Unit Injector (HEUI) {1100, 1126, 1250, 1251, 1261, 1290}
CB22, CB24, CB32 and CC24 Utility Compactors Hydraulic Tank Breather - Clean
785D OEM Off-Highway Truck Engine Air Precleaner - Clean
785D OEM Off-Highway Truck Engine Crankcase Breather - Clean
2008/02/18 New Tooling is Available to Assist During Disassembly and Assembly of the Ejector Bucket {6128}
New Abrasion Sleeve for the Cooler Hose of the Transmission{1375} New Abrasion Sleeve for the Cooler Hose of the Transmission{1375}
2007/12/24 An Improved Radiator Mount is Now Used on Paving Compactors {1351, 1353, 1374}
CB22, CB24, CB32 and CC24 Utility Compactors Battery or Battery Cable - Inspect/Replace
C4.4 Industrial Engine Belt Tensioner - Inspect