Tie Rod (Steering) - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove cotter pin (4). Loosen nut (5). Break the taper on tie rod (1). Remove nut (5).
- Loosen the bolt and nut (3).
- Repeat Step 1 and Step 2 for the other side.
- Remove tie rod (1) from link (2).
Note: For installation purposes, count and record the number of threads that are showing on tie rod (1).
Show/hide table
Illustration 1 | g01408485 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install tie rod (1) on link (2).
Note: Refer to the removal procedure for the recorded number of threads on tie rod (1).
- Tighten the bolt and nut (3). Tighten nut (3) to a torque of
75 ± 7 N·m (55 ± 5 lb ft) . - Install nut (5). Tighten nut (5) to a torque of
220 N·m (162 lb ft) plus the additional torque that is required to align the slots for installation of cotter pin (4). - Adjust the axle toe-in. Refer to Systems Operation, Testing and Adjusting, "Axle Toe-In (Front) - Adjust".
Show/hide table
Illustration 2 | g01408485 |
Caterpillar Information System:
904B, 906 and 908 Compact Wheel Loaders, IT14G and IT28G Integrated Toolcarriers and 914G, 924G, 924GZ, 928G and 930G Wheel Loaders Steering Column Play - Check
770 and 772 Off-Highway Trucks Power Train Transmission Planetary and Transfer Gears - Connect
770 and 772 Off-Highway Trucks Power Train Transmission Planetary and Transfer Gears - Separate
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Hydrostatic System - Test and Adjust" {4350, 4350}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Suction Fan
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Gear Motor (Fan Drive)
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Gear Pump (Steering)
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Steering Control Group
CP76 and CS76 Vibratory Compactors Machine Systems Piston Pump (Vibratory)
CS54 and CP54 Vibratory Soil Compactors Operator Controls
Rework Procedure For the 192-0086 Ride Control Valve Gp {5004, 5054} Rework Procedure For the 192-0086 Ride Control Valve Gp {5004, 5054}
CP76 and CS76 Vibratory Compactors Machine Systems Piston Pump Neutral (Vibratory) - Test and Adjust
2007/08/27 A New Chassis Harness is Now Available Without a Diode Which Will Prevent Engine Overheating on Asphalt Pavers {1408}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Muffler
CP54 and CS54 Vibratory Soil Compactors Machine Systems Hydraulic Cylinder (Cab Tilt)
770 and 772 Off-Highway Trucks Power Train Transmission Planetary and Transfer Gears - Remove
140M Motor Grader Engine Supplement Radiator - Install
770 and 772 Off-Highway Trucks Power Train Transmission Planetary and Transfer Gears - Install
TH580B Telehandler Fuel System Primary Filter (Water Separator) Element - Replace
14M and 16M Motor Graders Machine Systems Lubrication System - If Equipped
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Main Relief Valve - Test and Adjust" {5069, 5069}
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Line Relief Valve - Test and Adjust" {5117, 5117}
CP76 and CS76 Vibratory Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Worksheets - Troubleshoot" {4350, 5050}