Drum - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 8S-7640 | Stand | 2 |
| 8S-7611 | Tube | 2 | |
| 8S-7615 | Pin | 2 | |
- Use a suitable lifting device to position drum (13) in yoke (12). The weight of the drum is approximately 6150 kg (13550 lb). Install any shims that were removed in the original locations. Install bolts (14) on both sides of drum (13) .
Show/hide table
 | |
| Illustration 1 | g01406350 |
- Use the suitable lifting device to raise drum (13) and remove Tooling (A). Lower the drum to the floor.
- Position the hose assemblies for the vibratory motor between the yoke and the drum. Position the hose assemblies for the drum propel motor between the yoke and the drum.
Show/hide table
 | |
| Illustration 2 | g01406343 |
- Install clamp assembly (12) and the bolts on both sides of the yoke.
- Install guard (11) and the bolts on both sides of the yoke.
- Install clamps (10) .
Show/hide table
 | |
| Illustration 3 | g01406186 |
- Connect hose assemblies (8) and hose assemblies (7) to piston motor (9) .
Show/hide table
 | |
| Illustration 4 | g01406184 |
- Connect hose assemblies (6) to piston motor (5) .
Show/hide table
 | |
| Illustration 5 | g01406183 |
- Connect harness assemblies (4) and install the nuts.
Show/hide table
 | |
| Illustration 6 | g01406182 |
- Install bracket (2) and bolts (1) .
Show/hide table
 | |
| Illustration 7 | g01406181 |
- Install clamp (3) and the bolts.
End By:
- Install the front bumper. Refer to Disassembly and Assembly, "Front Bumper - Remove and Install".
- Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
CP54 and CS54 Vibratory Soil Compactors Machine Systems Air Conditioner Group
Fuel Sender Leaks on C-Series Multi Terrain Loaders and Skid Steer Loaders{1273} Fuel Sender Leaks on C-Series Multi Terrain Loaders and Skid Steer Loaders{1273}
14L Motor Grader Steering Frame Lock - Separate and Connect
2007/08/20 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/27 A New Battery Disconnect Switch Improves Battery Life {1402, 1411, 7257}
C7 and C9 Engines for Caterpillar Built Machines CID 0164 FMI 11 Injector Actuation Pressure system fault
2007/08/13 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/27 Improved Engine Software is Used {7620}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Front Bumper
770 and 772 Off-Highway Truck/Tractors Cab - Install
770 and 772 Off-Highway Truck/Tractors Cab - Remove
160M Motor Grader Machine Systems Secondary Steering Pump and Motor - Install
14L Motor Grader Gear Group (All Wheel Drive) - Remove
2007/08/27 An Improved Secondary Steering Valve Mount is Now Used {4339}
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Design
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump
PF-300B and PS-300B Pneumatic Compactors Maintenance Interval Schedule
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Nozzles
C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Design
CP76 and CS76 Vibratory Compactors Propel System Pump Drive
C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.5 and C2.2 Engines for Caterpillar Built Machines Rocker Shaft