Sloper - Check and Adjust
Adjustment of the Sloper Stop
Show/hide table
Illustration 1 | g01390566 |
For clarity, some components are missing from this illustration. |
Show/hide table
Illustration 2 | g00706407 |
- You will need a 1220 mm (48 inch) straight edge (5). Use the height control to raise the retracted extender above the main screed (4). Place the straight edge on the outside edge of the main screed.
Show/hide table
Illustration 3 | g01387487 |
Height Control |
- Loosen the jam nut for the sloper stop (2). Use the height control (7) in order to lower the extender until trailing edge (6) of the extender touches straight edge (5) .
- Move the straight edge to the inside edge of the main screed. Use the slope control (8) in order to raise the inside edge or lower the inside edge until the trailing edge of the extender touches the straight edge.
Show/hide table
Illustration 4 | g01387484 |
Slope Control |
- Verify that the outside edge of the extender is even with the main screed plate or below the main screed plate. Tighten the bolt for the sloper stop (3) until you feel resistance. Tighten jam nut (2) to a torque of 122 ± 14 N·m (90 ± 10 lb ft).
Adjusting the Pivot
Adjust the pivot for the extender if there is play. Tighten the nut on the pivot for the extender to a torque of 149 ± 14 N·m (110 ± 10 lb ft). Loosen the nut (1) for 3/4 of a full turn. Install a new cotter pin. Do not exceed the torque that is recommended.
Caterpillar Information System:
AS3251C Asphalt Screed Visual Inspection
AS3251C Asphalt Screed Machine Preparation for Troubleshooting
AS3251C Asphalt Screed Electric Heat System
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 156 - CID 1251 - FMI 08
450E Backhoe Loader Engine Supplement Fan Guard - Remove and Install
Procedure to Access the License Information for Caterpillar Electronic Technician (CAT ET){0785} Procedure to Access the License Information for Caterpillar Electronic Technician (CAT ET){0785}
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 039 - CID 0990 - FMI 08
450E Backhoe Loader Engine Supplement Electric Starting Motor - Remove and Install
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 082 - CID 0977 - FMI 08
450E Backhoe Loader Engine Supplement Side Panel - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Engine Supplement Engine - Install
CP54 and CS54 Vibratory Soil Compactors Engine Supplement Engine - Remove
2007/06/18 The Pressure Relief Valve for the Radiator Group is Updated {1353}
C9.3 Tier 4 Final Engines Engine Valve Lash - Inspect/Adjust
The Routing of the Battery and Wiring Group (Electric Start) Must be Changed on Specific Off-Highway Trucks{1402, 1408} The Routing of the Battery and Wiring Group (Electric Start) Must be Changed on Specific Off-Highway Trucks{1402, 1408}
AS3251C Asphalt Screed Heater Element - Test
450E Backhoe Loader Engine Supplement Alternator - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
450E Backhoe Loader Engine Supplement Refrigerant Compressor - Remove and Install
CB14 and CB14 XW Vibratory Compactor Machine Systems Engine Mounting
450E Backhoe Loader Engine Supplement Belt Tensioner - Remove and Install
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 082 - CID 0967 - FMI 09
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 156 - CID 0967 - FMI 09
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0967 - FMI 09