Circle - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 8S-7630     | 台架     | 1     |
8S-7621 | 管     | 1     | |
8S-7615 | 销     | 1     | |
8S-8048 | 鞍座     | 1     | |
B     | 138-7575     | 连杆支架     | 1     |
D     | 140-7742     | 套筒     | 2     |
E     | 9U-6600     | 手动液压泵     | 1     |
4C-9634 | 拉拔器螺柱     | 1     | |
6V-3170 | 双作用油缸     | 1     | |
1P-1835 | 轴承拆卸工具适配器     | 1     | |
9U-6832 | 螺母     | 1     | |
4K-0684 | 硬垫圈     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
在发动机和油泵停转后,本机器的液压系统中可能仍保持着液压油压力。 如果在对液压进行任何维护前没有释放此压力,可能会造成严重的人身伤害。 为了避免可能的人身伤害,在进行接头、软管或液压零部件操作之前应释放液压系统压力。 开始维护之前把所有机具降到地面。 如果必须在机具升起位置时维护、测试或调整液压系统,则需要适当支撑住机具和提升油缸。 一定要将机器移到远离其它机器行走线路的地方。 发动机运转并进行测试或调整时,应保证其他人员远离机器。 |
- 使用工具 (E) 将轴承 (25) 安装在转盘 (2) 上。 对其余的轴承 (25) 重复此步骤。
Show/hide table
图 1 | g01342152 |
- 清洁转盘主动小齿轮上的灰尘和油污。 将转盘 (2) 安装在牵引杆 (24) 下。 起动并运转发动机。 使用机器系统将牵引杆 (24) 安装在转盘 (2) 上。 关闭发动机。
Show/hide table
图 2 | g01341960 |
- 安装耐磨垫 (23) 和履带板 (22) 。 安装螺栓 (21) 。 拧紧螺母 (20) 。
Show/hide table
图 3 | g01341940 |
- 安装耐磨垫 (19) 。
Show/hide table
图 4 | g01342259 |
- 安装垫片 (18) 。
Show/hide table
图 5 | g01341971 |
- 安装板 (17) 。
Show/hide table
图 6 | g01341968 |
- 使用工具 (B) 和适当的起吊设备,以便安装旋转台座 (15) 。 旋转台座 (15) 的重量约为 41 kg (90 lb)。
Show/hide table
图 7 | g01341938 |
- 安装螺栓 (16) 。
- 安装螺栓 (13) 。 连接软管组件 (14) 。 连接软管组件 (12) 。
Show/hide table
图 8 | g01341932 |
- 起动并运转发动机。 开动机器以提升转盘 (2) ,然后卸下工具 (A) 。 转盘 (2) 的重量约为 1000 kg (2205 lb)。
Show/hide table
图 9 | g01341930 |
- 停止发动机,释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 测量耐磨垫 (19) 和转盘 (2) 之间的间隙 (A) 。 间隙 (A) 不得大于 0.50 mm (0.020 inch)。 添加或卸下垫片 (18) ,以达到恰当的间隙值。
Show/hide table
图 10 | g01342178 |
Show/hide table
图 11 | g01342512 |
- 拧松螺母 (20) 和螺栓 (21) ,以便可以在履带板 (22) 中移动。 将转盘主动小齿轮卡进转盘 (2) 的轮齿。 移动转盘 (2) ,使其与连接前履带板的转盘 (2) 达到间隙 (C) 。 间隙 (C) 必须为 50 + 2.50 − 0.50 mm (2.0 + 0.098 − 0.020 inch)。
- 均匀地调整履带板 (22) 的螺母 (20) ,使耐磨垫 (23) 与转盘 (2) 相连。 卸下螺母 (20) 以获得间隙 (B) 。 间隙 (B) 不得大于 0.80 mm (0.032 inch)。
- 拧紧螺栓 (21) 至扭矩 920 ± 60 N·m (679 ± 44 lb ft)。 拧紧螺母 (20) 至扭矩 570 ± 80 N·m (421 ± 59 lb ft)。
- 起动并运转发动机。 在整个作业范围转动转盘 (2) ,检查其是否固定。 转盘 (2) 必须可以自由转动。
- 停止发动机,释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 使用工具 (E) 将轴承 (11) 安装在铲刀组件 (3) 上。 对其余的轴承 (11) 重复此步骤。
Show/hide table
图 12 | g01342162 |
- 使用工具 (D) 和两个适当的起吊设备安装铲刀组件 (3) 。 铲刀组件 (3) 的重量约为 1814 kg (4000 lb)。
Show/hide table
图 13 | g01341921 |
Show/hide table
图 14 | g01341923 |
- 支撑铲刀组件 (3) ,防止铲刀 (3) 倾斜。 起动并运转发动机。 运行机器,将铲刀组件 (3) 连接在转盘 (2) 上。
Show/hide table
图 15 | g01341912 |
- 关闭发动机。
- 安装垫圈 (10) 和销 (9) 。
Show/hide table
图 16 | g01341910 |
- 拆下开口销 (6) 。 安装垫圈 (8) 和螺母 (7) 。
Show/hide table
图 17 | g01341906 |
- 连接软管组件 (5) 。 安装铲刀倾斜油缸 (4) 。 请参阅拆解和组装, "铲刀倾斜油缸 - 拆卸和安装"。
Show/hide table
图 18 | g01341901 |
- 起动并运转发动机。 提升转盘 (2) 和铲刀组件 (3) 以卸下适当的挡块。
Show/hide table
图 19 | g01341892 |
- 运行机器,将转盘中心移动锁销 (1) 固定在机器右边第三个位置。
Show/hide table
图 20 | g01342604 |
Caterpillar Information System:
14M Motor Grader Machine Systems Circle - Remove
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Fan and Gear Motor (Hydraulic Fan) - Install
2007/03/12 Maintenance Instruction Has Been Added for HMU Steering {4310, 4343}
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Top Speed Is Not Obtained
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Electrical Power Supply - Test
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Configuration Parameters
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Coolant Temperature Is High
3412E Engine for Caterpillar Built Machines System Overview
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Fuel Pressure Is Low
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Event Code List
14M Motor Grader Machine Systems Front Axle - Install
2007/01/22 A New Sprocket Bearing Improves Reliability for Multi Terrain Loaders {4164, 7551}
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Gear Motor (Hydraulic Fan) - Disassemble
777G Off-Highway Truck Power Train Rear Wheel, Bearing, and Duo-Cone Seal - Remove
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1401 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1402 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1403 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1404 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1405 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1406 - FMI 13
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Gear Motor (Hydraulic Fan) - Assemble
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Control Valve (Work Tool) - Install - High Flow
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Acceleration Is Poor or Throttle Response Is Poor
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Overspeeds