Front Axle - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7536     | 起吊台架     | 1     |
4C-5809 | 电动液压泵总成     | 1     | |
B     | 8S-7615     | 销     | 1     |
8S-7640 | 台架     | 1     | |
8S-7611 | 管     | 1     | |
C     | 1P-1835     | 轴承拆卸工具适配器     | 1     |
4C-9634 | 拉拔器螺柱     | 1     | |
6V-3170 | 双作用油缸     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6832 | 螺母     | 1     | |
D     | 1P-0510     | 冲头总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 降低轴承 (21) 的温度。 使用工具 (C) 安装轴承 (21) 。 在 (A) 处安装轴承 (21) 。 间隙 (A) 为 8.5 ± 0.5 mm (0.3346 ± 0.0197 inch)。
Show/hide table
图 1 | g01341366 |
Show/hide table
图 2 | g01341418 |
- 使用工具 (D) 安装唇形密封 (20) 。
Show/hide table
图 3 | g01341372 |
- 使用工具 (D) 安装唇形密封 (19) 。
Show/hide table
图 4 | g01341364 |
- 使用两台适当的起吊设备安装前轴 (13) 。 前轴 (13) 的重量约为 907 kg (2000 lb)。
Show/hide table
图 5 | g01341243 |
Show/hide table
图 6 | g01341245 |
- 安装工具 (B) 以支撑前轴 (13) 。
Show/hide table
图 7 | g01341344 |
- 安装垫圈 (18) 。
Show/hide table
图 8 | g01341343 |
- 安装垫圈 (17) 和板 (16) 。
Show/hide table
图 9 | g01341342 |
- 安装销组件 (15) 。 安装螺栓 (14) 。
Show/hide table
图 10 | g01341248 |
- 安装夹子 (12) 。 连接线束组件 (11) 。 连接线束组件 (10) 。
Show/hide table
图 11 | g01341199 |
- 连接软管组件 (9) 、软管组件 (8) 以及软管组件 (7) 。
Show/hide table
图 12 | g01341193 |
- 连接软管组件 (6) 、软管组件 (5) 、软管组件 (4) 、软管组件 (3) 和软管组件 (2) 。
Show/hide table
图 13 | g01341185 |
- 从牵引杆 (1) 和前轴上卸下工具 (A) 和工具 (B) 。
Show/hide table
图 14 | g01341167 |
End By:
- 安装车轮倾斜杆。 请参阅 拆解和组装, "车轮倾斜杆 - 拆卸和安装"。
- 安装前轮。 请参阅 拆解和组装, "车轮 - 拆卸和安装"。
Caterpillar Information System:
2007/01/22 A New Sprocket Bearing Improves Reliability for Multi Terrain Loaders {4164, 7551}
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Control Valve (Work Tool) - Remove - High Flow
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Power Train Solenoid Valve (Motor, 2-Speed) - Remove and Install
Frame Replacement for the 793B and 793C Off-Highway Trucks{1353, 7000, 7000, 7051} Frame Replacement for the 793B and 793C Off-Highway Trucks{1353, 7000, 7000, 7051}
PL61 Pipelayer and D6K Track-Type Tractor Using Caterpillar Electronic Technician to Determine Diagnostic Codes
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors C6.6 Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Connect
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors C6.6 Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Separate
14M Motor Grader Machine Systems Front Axle - Remove
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Radiator - Remove and Install
C4.4 and C6.6 Engines for Caterpillar Built Machines ECM Will Not Communicate with Other Systems or Display Modules
587R Pipelayer Safety Messages - Arrangement II (Cab)
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Aftercooler - Remove and Install
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Event Code List
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Fuel Pressure Is Low
3412E Engine for Caterpillar Built Machines System Overview
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Coolant Temperature Is High
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Configuration Parameters
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Electrical Power Supply - Test
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Top Speed Is Not Obtained
2007/03/12 Maintenance Instruction Has Been Added for HMU Steering {4310, 4343}
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Fan and Gear Motor (Hydraulic Fan) - Install
14M Motor Grader Machine Systems Circle - Remove
14M Motor Grader Machine Systems Circle - Install
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Gear Motor (Hydraulic Fan) - Disassemble