Wheel Spindle - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 1     |
开始:
- 拆下终传动和车轮。 请参阅拆解和组装, "终传动和车轮 - 拆卸"。
注: 下列步骤是对前车桥执行。 各车轮心轴具有相同的拆卸步骤。
- 将工具 (A) 和适当的起吊设备连接到车轮心轴 (2) 上。 车轮心轴 (2) 的重量约为 27 kg (60 lb)。
Show/hide table
图 1 | g01206032 |
- 拆下 16 个螺母 (1) 。 卸下车轮心轴 (2) 。
- 拆下 O 形密封圈 (4) 。
Show/hide table
图 2 | g01206033 |
拆下双头螺栓后车轮心轴视图。 |
Show/hide table
图 3 | g01206035 |
拆下双头螺栓后车轮心轴视图。 |
- 从车轮心轴拆卸 4 个螺栓 (3) 和座圈 (5) 。
- 从护圈 (5) 上卸下 O 形密封圈 (6) 。
Show/hide table
图 4 | g01206036 |
安装步骤
- 将 O 形密封圈 (6) 安装到座圈 (5) 上。
Show/hide table
图 5 | g01206036 |
- 将座圈 (5) 放置在车轮心轴上。 安装四个螺栓 (3) 。
Show/hide table
图 6 | g01206035 |
拆下双头螺栓后车轮心轴视图。 |
Show/hide table
图 7 | g01206033 |
拆下双头螺栓后车轮心轴视图。 |
- 将 O 形密封圈 (4) 在车轮心轴上安装到位。
- 将工具 (A) 和适当的起吊设备连接到车轮心轴 (2) 上。 车轮心轴 (2) 的重量约为 27 kg (60 lb)。
Show/hide table
图 8 | g01206032 |
- 将车轮心轴放置在 (2) 车桥组件上。 安装 16 个螺母 (1) 。 将螺母 (1) 拧紧至扭矩为 475 ± 50 N·m (350 ± 37 lb ft)。
End By: 安装终传动和车轮。 请参阅 拆解和组装, "终传动和车轮 - 安装"。
Caterpillar Information System:
R1600G Load Haul Dump Power Train Final Drive and Wheel - Remove
R1600G Load Haul Dump Power Train Final Drive and Wheel - Install
R1600G Load Haul Dump Power Train Final Drive and Wheel - Assemble
R1600G Load Haul Dump Power Train Final Drive and Wheel - Disassemble
AP-1000D and BG-260D Asphalt Pavers Machine Systems Hydraulic Cylinder (Screed Hoist)
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Relief Valve (Load Sensing Signal)
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Sensors
416E Backhoe Loader Extendable Stick Pads - Inspect/Adjust - If Equipped
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 1400 - FMI 06
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Install
AP-1000D and BG-260D Asphalt Pavers Machine Systems Electric Motor (Screed Burner Fuel Pump) - Remove and Install
793D Off-Highway Truck Power Train Transmission Hydraulic Control Clutch Pressure - Test
R1300G Series II Load Haul Dump Power Train Torque Converter Case
2005/10/17 An Increased Torque Replaces The Use of Anti-seize Compound on the Rear Wheel Group. {4201}
793D Off-Highway Truck Steering System Pressure Switches
793D Off-Highway Truck Power Train Transmission Hydraulic Control Shift Signal Pressure - Test
793D Off-Highway Truck Power Train Lubrication Relief Valve (Transmission) Pressure - Test
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System General Information
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Service Tools
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Diagnostic Capabilities
854K Wheel Dozer and 992K Wheel Loader Power Train Using the Operator Monitor to Determine Diagnostic Codes
G3304 and G3306 Engines Electric Starting Motor
793D Off-Highway Truck Air System and Brakes Hoist and Brake System Troubleshooting