Electric Motor (Screed Burner Fuel Pump) - Remove and Install
Show/hide table
 |
|
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g01201034 - Remove nuts (1) and cover (2).
Show/hide table
Illustration 2 g01201041 - Remove nuts (3) and disconnect harness assemblies (6).
- Disconnect hose assemblies (7).
- Remove bolts (5) and electric motor (4).
Show/hide table
Illustration 3 g01205840 - Remove fuel filter (11) from electric motor (4).
- Remove bolts (10) and remove screed burner fuel pump (8) from electric motor (4).
- Loosen the set screw and remove coupling (9) from screed burner fuel pump (8).
- Install coupling (9) on screed burner fuel pump (8) and tighten the set screw.
- Install screed burner fuel pump (8) on electric motor (4) and install bolts (10).
- Install fuel filter (11) on electric motor (4).
Show/hide table
Illustration 5 g01201041 - Install bolts (5) and electric motor (4).
- Connect hose assemblies (7).
- Connect harness assemblies (6) and install nuts (3).
Show/hide table
Illustration 6 g01201034 - Install cover (2) and nuts (1).
- Turn the battery disconnect switch to the ON position.
Show/hide table
| |
| Illustration 4 | g01205840 |
Caterpillar Information System:
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
793D Off-Highway Truck Air System and Brakes Relief Valve (Brake Oil Cooler) - Test and Adjust
M325D MH Material Handler Air Conditioning and Heating Control
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Configure
CB-534D, CB-534D Series XW and CB-564D Vibratory Compactors Engine Supplement Fuel Priming Pump and Fuel Filter Base - Remove and Install
D7R Series 2 Track-Type Tractor Power Train Bevel and Transfer Gears
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Remove
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Install
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Disassemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Assemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Disassemble
R1300G Series II Load Haul Dump Power Train Output Drive
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Install
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 1400 - FMI 06
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
416E Backhoe Loader Extendable Stick Pads - Inspect/Adjust - If Equipped
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Sensors
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Relief Valve (Load Sensing Signal)
AP-1000D and BG-260D Asphalt Pavers Machine Systems Hydraulic Cylinder (Screed Hoist)
R1600G Load Haul Dump Power Train Final Drive and Wheel - Disassemble
R1600G Load Haul Dump Power Train Final Drive and Wheel - Assemble
R1600G Load Haul Dump Power Train Final Drive and Wheel - Install
R1600G Load Haul Dump Power Train Final Drive and Wheel - Remove
R1600G Load Haul Dump Power Train Wheel Spindle - Remove and Install