Bevel and Transfer Gears
Show/hide table
 | |
| 图 1 | g02725680 |
Show/hide table
| 244-2616 伞齿轮和分动器 、 162-6874 伞齿轮和分动器 和 166-3485 伞齿轮和分动器 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 2 | 1 | 9P-1922 垫片组 | 根据需要，使用厚度为 2.01 mm (0.079 in) 的垫片组达到 0.10 ± 0.05 mm (0.004 ± 0.002 in) 的端隙。 |
| 3 | 1 | 0S-1569 螺栓 | 拧紧至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。 |
| 4 | 12 | 0L-1169 螺栓 | 拧紧至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。 |
| 5 | 24 | 7B-3235 螺栓 | 拧紧至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。 |
| 6 | 4 | 0S-1591 螺栓 | 拧紧至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。 |
| 7 | 1 | 216-0273 唇形密封件 | 用润滑剂稍微润滑即将密封的密封唇。 |
| 8 | 1 | 9P-1921 垫片组 | 根据需要，使用厚度为 2.01 mm (0.079 in) 的垫片组达到 0.10 ± 0.05 mm (0.004 ± 0.002 in) 的端隙。 |
Show/hide table
 | |
| 图 2 | g02725681 |
Show/hide table
| 244-2616 伞齿轮和分动器 、 162-6874 伞齿轮和分动器 和 166-3485 伞齿轮和分动器 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 9 | 1 | 1L-6957 轴承锁紧螺母 | 装配前，在螺纹上涂抹 Loctite C5A。 |
| 拧紧至扭矩为 612 ± 68 N·m (451 ± 50 lb ft)。 |
|||
| 10 | 2 | 9P-1478 垫片组 | 根据需要，使用厚度为 2.7 mm (0.11 in) 的垫片组以达到齿隙。 采用以下步骤达到齿隙： |
| 1. 利用适当的螺纹固定件 (1) 防止小齿轮转动。 | |||
| 2. 设置齿隙的同时，将固定件拧紧至最大扭矩为 7 N·m (62 lb in)。 |
|||
| 3. 拆下固定件。 | |||
| 4. 移除轴承组件的端隙后应检查齿隙，齿隙必须为 0.20 to 0.42 mm (0.008 to 0.017 in)。 |
|||
| 5. 在三个等距分布的齿上测量齿隙。 | |||
| 6. 齿的间隙不得大于 0.15 mm (0.006 in)。 |
|||
| 11 | 12 | 0S-1897 螺栓 | 拧紧至扭矩为 475 ± 60 N·m (350 ± 44 lb ft)。 |
| 12 | 4 | 1D-4601 螺栓 | 拧紧至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。 |
参考有关调整下分动器齿轮和上分动器以及小锥齿轮的步骤，请参考拆解和装配伞和分动器齿轮, " - 组装"。
Caterpillar Information System:
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Remove
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Install
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Disassemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Assemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Disassemble
R1300G Series II Load Haul Dump Power Train Output Drive
R1300G Series II Load Haul Dump Power Train Transmission Hydraulic Control
R1300G Series II Load Haul Dump Power Train Temperature Sensor (Transmission Oil)
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
777F Off-Highway Truck Rear Axle A-Frame Bearing - Lubricate
793D Off-Highway Truck Air System and Brakes Parking and Secondary Brake Release System Leakage - Check
3516B Off-Highway Trucks Pulse Width Modulated Sensor
CB-534D, CB-534D Series XW and CB-564D Vibratory Compactors Engine Supplement Fuel Priming Pump and Fuel Filter Base - Remove and Install
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Configure
M325D MH Material Handler Air Conditioning and Heating Control
793D Off-Highway Truck Air System and Brakes Relief Valve (Brake Oil Cooler) - Test and Adjust
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
AP-1000D and BG-260D Asphalt Pavers Machine Systems Electric Motor (Screed Burner Fuel Pump) - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Install
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 1400 - FMI 06
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
416E Backhoe Loader Extendable Stick Pads - Inspect/Adjust - If Equipped
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Sensors
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Relief Valve (Load Sensing Signal)