Ejector Cylinder Mounting Group - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 180-3033 | 修理台架 | 1 |
B | 8B-7544 | 轴承拉拔器 | 1 |
8B-7549 | 拉拔器支腿 | 2 | |
3H-0465 | 推拉板 | 4 | |
1B-4207 | 全高螺母 | 2 | |
5P-4808 | 盖 | 2 | |
1U-9895 | 十字挡块 | 1 | |
5B-0637 | 高怠速螺母 | 1 | |
5F-7353 | 垫圈 | 1 | |
8S-6586 | 顶出螺钉 | 1 |
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
吊装或垫塞不当可能会造成人员伤亡。 当使用起重机或千斤顶顶升任何零件或部件时,与之保持距离。 确保起重机或千斤顶具备正确的部件吊装能力。 在沉重部件下面进行任何工作之前先安装垫块或台架。 图上显示的是部件的近似重量。 清洁要安装零件的所有表面。 |
- 机器应停放在水平地面上。 部分伸出推料器油缸。 装上转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
- 为便于安装,在所有管路、软管及管上做出识别标记。 插接好所有管路、软管和管。 这将有助于防止油液损失以及污染机油系统。
Show/hide table
图 1 g01196754 - 起动发动机。 伸出推料器油缸,使推料器铲刀有一半在推料器本体上。 使工具 (A) 有充分的安置空间。 停止发动机并将断路开关转到断开位置。
Show/hide table
图 2 g01196763 - 松开推料器铲刀两侧的螺母 (2)。 转动推料器铲刀两侧的螺栓 (1),以将底板滚轮升离卡车车斗底板。
注: 拆卸和安装安装总成的过程中,升起底板滚轮以防推料器铲刀移动。
Show/hide table图 3 g01193678 - 断开软管组件 (3)。
Show/hide table
图 4 g01193693 Show/hide table图 5 g01193679 - 将适当的起吊设备固定到推料器油缸 (4) 以支撑住推料器油缸 (4) 和万向接头 (5)。 推料器油缸 (4) 和万向接头 (5) 的组合重量约为
478 kg (1054 lb) 。 - 拆下螺栓 (6)。 拆下板 (7) 和垫片 (8)。
- 拆下螺栓 (9)。 拆下板 (10) 和垫片 (11)。
Show/hide table
图 6 g01193683 - 从板 (7) 上卸下螺栓 (12) 和盖 (13)。 对板 (10) 重复步骤。
Show/hide table
图 7 g01193692 - 使用工具 (B),从板 (7) 上卸下轴承 (14)。 对板 (10) 重复步骤。
Show/hide table
图 8 g01193680 - 松开万向接头 (5) 两侧的螺栓 (15)。 此时不要拆下两个螺栓 (15)。 拆下螺栓 (16) 并拆下万向接头 (5) 两侧的盖 (17)。
Show/hide table
图 9 g01193684 - 拆下螺栓 (18)、垫圈 (19)、隔套 (20) 和隔套 (21)。 记下万向接头 (5) 两侧所有垫圈和隔套的位置,以便于安装。
Show/hide table
图 10 g01193685 - 缓慢地缩回推料器油缸,以将万向接头 (5) 从推料器铲刀分离。 拆下万向接头 (5) 两侧的支架 (22) 和套筒 (23)。
Show/hide table
图 11 g01193686 - 缩回推料器油缸 (4),以提供拆卸万向接头 (5) 的充足空间。 将推料器油缸 (4) 降至工具 (A) 上。
- 将两个适当的起吊设备安装到万向接头 (5) 上以支撑住万向接头 (5),如图所示。 万向接头 (5) 的重量大约为
115 kg (254 lb) 。 - 拆下螺栓 (15) 和轴承盖 (24)。 对万向接头 (5) 的另一侧重复该步骤。
Show/hide table
图 12 g01196758 - 将万向接头 (5) 从机器上拆下。 将轴承 (25) 和垫圈 (26) 从推料器油缸 (4) 的两侧拆下。
Caterpillar Information System:
2006/11/20 New Service Parts are Available for Hydraulic Motors on Cold Planers and Wheel Saws {5058, 7000}
14M and 16M Motor Graders Machine Systems Blade Lift
793D Off-Highway Truck Steering System Piston Pump (Steering)
793D Off-Highway Truck Power Train Transfer Gears
RM-300 Reclaimer Mixer Machine Systems Electrical System (Auxiliary Hydraulic)
793F and 793F CMD Off-Highway Truck Braking System Gear Pump (Brake Cooling)
RM-300 Reclaimer Mixer Machine Systems Operator Controls (Rotor Drive System)
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Power Train Torque Converter and Transmission Pressures
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Switches
966H Wheel Loader and 972H Wheel Loader Power Train Backup Alarm Always Off
966H Wheel Loader and 972H Wheel Loader Power Train Backup Alarm Always On
730 EJECTOR and 740 EJECTOR Articulated Trucks Ejector Blade Carriage - Install
730 EJECTOR and 740 EJECTOR Articulated Trucks Ejector Cylinder Mounting Group - Install
RM-300 Reclaimer Mixer Machine Systems Position Sensor (Rotor Depth, Front Steering, and Rear Steering)
14M and 16M Motor Graders Machine Systems Drawbar
14M and 16M Motor Graders Hydraulic and Steering System Control Valve (Blade Tip)
RM-300 Reclaimer Mixer Machine Systems Metering Pump (Steering)
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Assemble
24M Motor Grader Hydraulic and Steering System Control Valve (Ripper)
966H Wheel Loader and 972H Wheel Loader Steering System Steering System Troubleshooting
RM-300 Reclaimer Mixer Machine Systems Control Valve (Front Auxiliary Manifold)
R1600G Load Haul Dump Machine Systems Solenoid Valve (Lift Arm Positioner) - Remove and Install
R1600G Load Haul Dump Machine Systems Cab - Remove
R1600G Load Haul Dump Machine Systems Cab - Install