Cab - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Description | Qty |
| A | 138-7575 | Link Bracket | 4 |
Start By:
- Connect steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Show/hide table
 |
|
At operating temperature, the engine coolant is hot and under pressure. Steam can cause personal injury. Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure. Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 1 g01080662 View of rear of the cab - Disconnect two harness assemblies (4). Disconnect hose assembly (3). Disconnect hose assemblies (2) and (1). .
Show/hide table
Illustration 2 g01080677 - Remove nut (6) and disconnect ground strap (5) from the left rear of the cab.
Show/hide table
Illustration 3 g01080685 - Disconnect hoses (7) from the bottom of the cab.
Show/hide table
Illustration 4 g01080687 - Remove pin (8). Loosen nut (10) and remove parking brake cable (9).
Show/hide table
Illustration 5 g01080801 - Remove bolts (11) that hold the steering link assembly and the steering lever to the steering shaft. Place the steering link assembly out of the way. Remove the two bolts that hold brake valve (12) to the bottom of the cab.
Show/hide table
Illustration 6 g01080692 - Attach a suitable lifting device with Tooling (A) to cab (13), as shown. The weight of cab (13) is approximately
1225 kg (2700 lb) .Show/hide table
Illustration 7 g01080695 - Remove bolts (14) and remove the cab.
Caterpillar Information System:
C11 and C15 Engines for Caterpillar Built Machines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C11 and C15 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
PS-150C Pneumatic Compactor Machine System Air on the Run System Troubleshooting
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Axle Housing and Flange - Disassemble
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Relief Valve (Implement) - Test and Adjust
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Axle Housing and Flange - Remove
2004/08/30 New Bolts Are Used for the Pins on the Brake Group {4251}
R2900G Load Haul Dump Machine Systems Neutralizer Valve (STIC Steering) - Remove and Install
Procedure For Connecting Wire Harnesses To Work Tools{1408, 6060, 6634, 6701, 6706, 6712, 6715} Procedure For Connecting Wire Harnesses To Work Tools{1408, 6060, 6634, 6701, 6706, 6712, 6715}
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Brake Control Valve (Service)
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Aftercooler - Remove and Install
2005/04/04 Hitch Pins Are Now Available for the Bumper {7116}
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Axle Housing and Flange - Assemble
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Axle Housing and Flange - Install
2004/06/21 New Software Updates for the IQAN Software Are Now Used on the Track Feller Bunchers {7620}
2004/06/21 New Pressure Sensor Is Now Used {5574}
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove
Guidelines for the Use of High Efficiency Filters for the Hydraulic Oil System and for the Power Train Oil System {3000, 3004, 5050, 5068} Guidelines for the Use of High Efficiency Filters for the Hydraulic Oil System and for the Power Train Oil System {3000, 3004, 5050, 5068}
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Cab - Install
988H Wheel Loader Power Train Oil Coolers and Cooling System Operation
2004/06/28 A New Parking Brake Knob is Now Used {3065}
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Hood and Engine Enclosure - Remove
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Hood and Engine Enclosure - Install
2004/07/05 A New Radiator Has Improved Durability {1353}