Transmission Oil Cooler - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 2 |
| B | Rod 500 mm (19.68 inch) X 3.81 mm (0.15 inch) |
1 | |
Note: Check the O-ring seals, the gaskets and the seals for wear or damage. Replace the components, if necessary.
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) in order to clean each tube of the transmission oil cooler.
Show/hide table
 | |
| Illustration 1 | g01060136 |
Typical example | |
- Install Tooling (A) to the transmission oil cooler.
Show/hide table
 | |
| Illustration 2 | g01060131 |
Show/hide table
 | |
| Illustration 3 | g01060132 |
- Attach a hoist and suitable lifting chains to Tooling (A). The weight of the transmission oil cooler is approximately 20 kg (44 lb).
- Connect tube (7) to the transmission oil cooler.
- Install bonnet (11) .
- Install four bolts (10) .
- Install mounting bolts (9), the nuts, the washers and the spacers.
- Connect hose assembly (8) to the transmission oil cooler.
- Place housing (1) in position on the transmission oil cooler.
Show/hide table
 | |
| Illustration 4 | g01060130 |
- Install four bolts (3), four bolts (4), bolt (5) and bolt (6). Starting with bolt (5) (not shown) and bolt (6) (not shown), tighten all bolts evenly.
- Connect tube (2) to housing (1) .
Show/hide table
 | |
| Illustration 5 | g01060129 |
- Fill the cooling system with coolant. The capacity of the cooling system is 67 L (18 US gal). Refer to Operation and Maintenance Manual, SEBU7329, "Cooling System Coolant (DEAC) - Change". Or refer to Operation and Maintenance Manual, SEBU7329, "Cooling System Coolant (ELC) - Change".
End By:
- Install the engine bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Engine) - Remove and Install".
- Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Caterpillar Information System:
R2900G Load Haul Dump Power Train Steering Frame Lock - Separate and Connect
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 1403 - FMI 05
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 0622 - FMI 04
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 0622 - FMI 03
2007/08/13 New Planetary Parts Are Used to Reduce Wear of the Thrust Disc {3160}
M325D Material Handler Power Train Final Drive - Assemble
AP-1000B and BG-260C Asphalt Pavers Daily Inspection
AP-1000B and BG-260C Asphalt Pavers Maintenance Interval Schedule
SCJ and 8SC Series Alternators Charging System
SCJ and 8SC Series Alternators Service Tools
2004/03/22 A Check Valve is Now Available for The Water Spray Nozzles {5612}
267B, 277B and 287B Multi Terrain Loaders Power Train Idler Wheel - Remove - 287 Multi Terrain Loader
R1300G Load Haul Dump 3306 Engine Supplement Hydraulic Oil Cooler - Remove
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Quick Coupler - Remove and Install
2004/06/01 Realignment of Air System Components is Recommended. {1063}
769D Off-Highway Truck and 771D Quarry Truck Safety Messages
PS-150C Pneumatic Compactor Machine System Rollover Protective Structure (ROPS)
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Hydraulic System Pressure - Release
267B, 277B and 287B Multi Terrain Loaders Power Train Idler Wheel - Install - 287 Multi Terrain Loader
PS-150C Pneumatic Compactor Machine System Fuel Tank
CB-214E, CB-224E and CB-225E Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Wheel Propel) - Test - CB-225E
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Control Valve (Intermittent Saw) - If Equipped
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Bank Valve - Disassemble
2004/03/22 A New Retainer Plate For The Final Drive Bearing And Thrust Washer Improves The Service Life {4050}