Water Pump - Assemble
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| D | 1P-0510 | 冲头总成 | 1 |
| E | 138-9299(1) | 密封工具 | 1 |
| E | 488-2672(2) | 密封工具 | 1 |
| F | 139-0088(1) | 密封工具 | 1 |
| F | 325-5756(2) | 密封工具 | 1 |
Show/hide table
| (1) | 与 |
| (2) | 与 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁水泵轴 (6) 和壳体 (1) 中唇形密封 (9) 的沉孔。
- 使用工具 (D) ，将新的唇形密封 (9) 安装到壳体 (1) 中。
注: 安装密封时使密封金属表面上的零件号朝向壳体。 确保唇形密封与壳体沉孔的前边缘平齐。 请勿润滑唇形密封。 使用压具安装唇形密封。 请勿用手安装唇形密封。
- 将轴承组件 (8) 安装在水泵轴 (6) 上。
- 安放挡圈 (5)，使 “OUTSIDE”（外侧）标记朝向水泵轴 (6) 的齿轮端。
- 利用压具将齿轮 (2) 安装到水泵轴 (6) 上。
注: 安装齿轮 (2)，使其紧贴轴承组件 (8)。
- 将工具 (E) 在轴 (6) 的上方滑动。 锥边缘将朝向外侧。
- 将齿轮 (2) 和水泵轴安装到壳体 (1) 中。 小心不要损坏唇形密封 (9)。 安装将轴承挡圈 (5) 固定在壳体上的螺栓 (3) 。
- 将工具 (E) 从水泵轴 (6) 上拆下。
- 利用压具和工具 (F) 将新密封总成 (7) 安装到轴 (6) 上和壳体 (1) 中。 确保密封外侧壳体完全座入壳体中。
- 将叶轮 (4) 在水泵轴 (6) 上放置到位。 利用压具将叶轮 (4) 安装到水泵轴上。
注: 在水泵轴端部
0.00 ± 0.25 mm (0.000 ± 0.010 inch) 范围内安装叶轮 (4)。 - 将 O 形密封圈 (10) 安装在壳体上。
Show/hide table
| |
| 图 1 | g01021798 |
结束:
- 安装水泵。 请参阅拆解和组装, "水泵-安装"。
Caterpillar Information System:
248B and 268B Skid Steer Loaders Machine Systems Lift Arm Cylinder and Mounting
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Axle (Front)
572R Series II Pipelayer Equalizer Bar
572R Series II Pipelayer Hydraulic System Pressure Reducing Valve - Test and Adjust
572R Series II Pipelayer Hydraulic System Load Sense Manifold - Test and Adjust
572R Series II Pipelayer Hydraulic System Troubleshooting
572R Series II Pipelayer Hydraulic System Hydraulic Tank and Filter
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Lift Arm Cylinder and Mounting
572R Series II Pipelayer Power Train General Information
2003/10/06 Use 1U-9891 Hydraulic Oil Additive to Eliminate Brake Chatter and Reduce Noise in the Limited Slip Differential {3263, 5095}
572R Series II Pipelayer Hydraulic System Load Sense Manifold
572R Series II Pipelayer Hydraulic System Check Valve
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Parking Brake Control
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines General Information
2003/09/01 Oversized Bearings are Available for Reconditioning of Remanufactured Engine Oil Pumps and Scavenge Oil Pumps {1304, 1312}
2003/09/01 Oversized Bearings are Available for Reconditioning of Remanufactured Engine Oil Pumps and Scavenge Oil Pumps {1304, 1312}
C15 and C18 Engines for Caterpillar Built Machines Electronic Control System Components
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Service Brake Control
572R Series II Pipelayer Power Train Relief Valve (Transmission) - Test and Adjust
267, 277 and 287 Multi Terrain Loaders Engine Supplement Electric Starting Motor - Remove and Install - 287 Multi Terrain Loaders
267, 277 and 287 Multi Terrain Loaders Engine Supplement Alternator - Remove and Install - With Air Conditioning
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Front)
CP-323C and CS-323C Vibratory Compactors Engine Supplement Water Separator (Primary Fuel Filter) - Assemble