Lift Arm Cylinder and Mounting
Show/hide table
 | |
| Illustration 1 | g03774248 |
Show/hide table
| Specification for 218-5899 Lift Arm Cylinder and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| Before assembly, all pins, bores, and bearings must be clean. All pins, bores, and bearings must be lubricated with black 5P-0960 Grease Cartridge that is being sealed. Lubricate the entire cylindrical surface of all pins. | |||
| 1 | 2 | 287-3787 Pin As | Diameter is 38.03 ± 0.03 mm (1.497 ± 0.001 inch). Length is 101.0 ± 1.5 mm (3.98 ± 0.06 inch). |
| 2 | 2 | 190-8037 Pin As | Diameter is 44.38 ± 0.03 mm (1.747 ± 0.001 inch). Length is 242.0 ± 1.5 mm (9.53 ± 0.06 inch). |
| 3 | 2 | 142-9093 Pin | Diameter is 38.03 ± 0.03 mm (1.497 ± 0.001 inch). Length is 150.0 ± 1.5 mm (5.91 ± 0.06 inch). |
| 4 | 2 | 190-8038 Pin As | Diameter is 38.03 ± 0.03 mm (1.497 ± 0.001 inch). Length is 215.0 ± 1.5 mm (8.46 ± 0.06 inch). |
| 5 | 4 | 142-9091 Pin As | Diameter is 38.03 ± 0.03 mm (1.497 ± 0.001 inch). Length is 125.0 ± 1.5 mm (4.92 ± 0.06 inch). |
| 6 | 2 | 190-8036 Pin | Diameter is 44.38 ± 0.03 mm (1.747 ± 0.001 inch). Length is 155.0 ± 1.0 mm (6.10 ± 0.04 inch). |
| 7 | 2 | 190-8033 Pin As | Diameter is 38.03 ± 0.03 mm (1.497 ± 0.001 inch). Length is 167.0 ± 0.5 mm (6.57 ± 0.02 inch). |
| 8 | 4 | 6V-7700 Retaining Ring | Internal diameter is 40.59 to 41.43 mm (1.598 to 1.631 inch). Thickness is 1.57 ± 0.08 mm (0.062 ± 0.003 inch). |
| 9 | 2 | 3K-2151 Bushing | Internal diameter after assembly is 38.260 ± 0.020 mm (1.5063 ± 0.0008 inch). |
| 10 | 2 | 2G-8624 Bushing | Internal diameter after assembly is 44.59 ± 0.05 mm (1.756 ± 0.002 inch). |
| 11 | 2 | 191-9739 Bolt | Torque to 55 ± 10 N·m (41 ± 7 lb ft). |
Caterpillar Information System:
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Axle (Front)
572R Series II Pipelayer Equalizer Bar
572R Series II Pipelayer Hydraulic System Pressure Reducing Valve - Test and Adjust
572R Series II Pipelayer Hydraulic System Load Sense Manifold - Test and Adjust
572R Series II Pipelayer Hydraulic System Troubleshooting
572R Series II Pipelayer Hydraulic System Hydraulic Tank and Filter
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Lift Arm Cylinder and Mounting
572R Series II Pipelayer Power Train General Information
2003/10/06 Use 1U-9891 Hydraulic Oil Additive to Eliminate Brake Chatter and Reduce Noise in the Limited Slip Differential {3263, 5095}
572R Series II Pipelayer Hydraulic System Load Sense Manifold
572R Series II Pipelayer Hydraulic System Check Valve
572R Series II Pipelayer Hydraulic System Pressure Reducing Valve
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Parking Brake Control
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines General Information
2003/09/01 Oversized Bearings are Available for Reconditioning of Remanufactured Engine Oil Pumps and Scavenge Oil Pumps {1304, 1312}
2003/09/01 Oversized Bearings are Available for Reconditioning of Remanufactured Engine Oil Pumps and Scavenge Oil Pumps {1304, 1312}
C15 and C18 Engines for Caterpillar Built Machines Electronic Control System Components
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Service Brake Control
572R Series II Pipelayer Power Train Relief Valve (Transmission) - Test and Adjust
267, 277 and 287 Multi Terrain Loaders Engine Supplement Electric Starting Motor - Remove and Install - 287 Multi Terrain Loaders
267, 277 and 287 Multi Terrain Loaders Engine Supplement Alternator - Remove and Install - With Air Conditioning
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Front)