Differential and Final Drive Oil - Change
Show/hide table
增压系统:高温油可能会造成严重烧伤事故。 如需打开塞子,关闭发动机,等待直至轮轴冷却。 然后慢慢松开塞子,释放压力。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
注: 定期在 1 根车桥上执行这项步骤。
- 定位车轮,使终传动排放螺塞 (1) 处于最低位置。 这可确保终传动加注口螺塞 (2) 处在正确位置。
- 按下各个车桥断路器安全阀顶上的按钮,以便释放所有压力。
注: 有关轴向断路器安全阀的位置,请参考操作和保养手册, "轴向断路器安全阀 - 清洁"。
- 卸下终传动排放塞 (1),将机油排放到适当的容器中。
- 清洁并安装排放塞。
- 对于其它终传动,重复步骤 2 至 4。
Show/hide table
图 2 g01449382 前桥 Show/hide table图 3 g01449380 后桥 - 拆下前差速器放油塞 (3),让油排入一个合适的容器。
- 清洁并安装排放塞。
- 拆下加注口螺塞 (4)。 向差速器加注 SAE 50 机油,直到油位达到加注口螺塞开口底部。
- 清洁并安装加注口塞。
- 拆下终传动加油口螺塞 (2)。 向终传动加注 SAE 50 机油,直到油位达到加注口螺塞开口底部。
- 清洁并安装加注口塞。
- 对于其它终传动,重复步骤 10 至 11。
注: 为每根车桥加注
4.7 L (5 qt) 的 1U-9891 添加剂。注: 有关每个车桥的加注容量,请参阅操作和保养手册, "润滑油粘度和加注容量"。
- 如果指定容量的油不合终传动的要求,把终传动的加注口螺塞装上。 在平整的地面上让机器运转数分钟,使车桥的油位均衡。 把终传动的加注口螺塞卸下,再把剩余的机油注入。
- 让机器运转数分钟,再次检查油位。 在加注口螺塞开口底部应能看见油位。
如果油位高出加注口螺塞开口,不要将机油排出至正确的油位。 安装加注口塞。
- 对其余的差速器和终传动,重复这项步骤。
Show/hide table
图 1 | g01449379 |
Caterpillar Information System:
854K Wheel Dozer Case Drain Oil Filters - Replace
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1402 - FMI 03
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1401 - FMI 06
904H Compact Wheel Loader Cab Door
992K Wheel Loader Electrohydraulic System Boom Lift Speed - Check
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1401 - FMI 05
2008/03/24 Improved Track Seals for the Links are Now Used {4169, 4171, 4174, 4175}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1401 - FMI 03
992K Wheel Loader and 854K Wheel Dozer Power Train Axle Oil Cooler Pump and Motor - Install
992K Wheel Loader Machine Systems Ride Control Accumulator - Remove and Install
IT38H Integrated Toolcarrier and 938H Wheel Loader Ether Starting Aid Cylinder - Replace - If Equipped
993K Wheel Loader Power Train Torque Converter - Remove
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1402 - FMI 05
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1402 - FMI 06
3176C and 3196 Marine Engines Aftercooler Core - Clean/Test
992K Wheel Loader and 854K Wheel Dozer Power Train Modulating Valve (Torque Converter Lockup Clutch) - Remove and Install
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1403 - FMI 03
854K Wheel Dozer Differential and Final Drive Oil Level - Check
992K Wheel Loader and 854K Wheel Dozer Power Train Modulating Valve (Torque Converter Impeller Clutch) - Remove and Install
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1403 - FMI 05
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1403 - FMI 06
854K Wheel Dozer and 992K Wheel Loader Power Train Connector Contact Description
854K Wheel Dozer Differential and Final Drive Oil Sample - Obtain
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 1403 - FMI 13