Aftercooler - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 140-7742     | Sleeve     | 1     |
B     | 138-7573     | Link Bracket     | 1     |
Note: Cleanliness is an important factor. Before you begin the installation procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Attach Tooling (B) and a suitable lifting device to aftercooler (17). Install aftercooler (17). The weight of aftercooler (17) is approximately 18 kg (40 lb). Install bolts (18) .
Show/hide table
Illustration 1 | g01410357 |
Show/hide table
Illustration 2 | g01410576 |
- Install hose (14). Tighten the clamp on hose (14) to a torque of 12 ± 1 N·m (106 ± 9 lb in). Install bolt (15) .
Show/hide table
Illustration 3 | g01410339 |
- Repeat Step 2 for the other side. Install plate (16) .
- Position core assembly (10). Install bolts (11). Install bolt (12) .
Show/hide table
Illustration 4 | g01410321 |
- Repeat Step 4 for the other side. Install plate (13) .
- Use a suitable lifting device and Tooling (A) in order to support bracket assembly (6). Install bracket (8). Install bracket assembly (6) and bolts (7). Install bolts (9) .
Show/hide table
Illustration 5 | g01410179 |
- Install hose (4). Tighten the clamp on hose (4) to a torque of 12 ± 1 N·m (106 ± 9 lb in). Install bolts (5) .
Show/hide table
Illustration 6 | g01410066 |
- Repeat Step 7 for the other side.
- Position bracket assembly (3). Install bolt (1). Install bolts (2) .
Show/hide table
Illustration 7 | g01410062 |
End By:
- Install the hydraulic oil cooler. Refer to Disassembly and Assembly, "Hydraulic Oil Cooler - Remove and Install".
- Install the engine enclosure. Refer to Disassembly and Assembly, "Engine enclosure - Remove and Install".
Caterpillar Information System:
3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Top Speed Is Not Obtained
CS54 and CP54 Vibratory Soil Compactors Hydraulic System Oil Level - Check
3176C, 3406E and 3456 Industrial Engines Engine Shutdown Is Intermittent
CP76 and CS76 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Misfires, Runs Rough or Is Unstable
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
3176C, 3406E and 3456 Industrial Engines Engine Cranks but Does Not Start
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Engine and Machine Warm-Up
3176C Engine for Caterpillar Built Machines ECM Does Not Communicate with Other Modules
Supplemental Parts Information for the USN Seabee AP655C{1000, 7000} Supplemental Parts Information for the USN Seabee AP655C{1000, 7000}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Coolant Temperature Is High
Cat® Digital Voltage Regulator Generator Overcurrent - Troubleshoot
R1600G Load Haul Dump Braking System Brake Disc Wear - Check
R1600G Load Haul Dump Braking System Parking Brake - Manual Release
R1600G Load Haul Dump Machine Systems Steering Cylinder - Remove
R1600G Load Haul Dump Machine Systems Main Control Valve - Remove
R1600G Load Haul Dump Machine Systems Main Control Valve - Install
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Remove
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Install
2007/09/24 An Improved Fuse and ARC Suppressor is Now Used in the Axle Oil Cooler Wiring Harness {1365, 1408}
140H and 160H Motor Graders Changing Direction and Speed
3176C Engine for the R1600G and the R1700G Load Haul Dumps Oil Pressure Is Low
3176C Engine for the R1600G and the R1700G Load Haul Dumps Power Is Intermittently Low or Power Cutout Is Intermittent
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed Control (Remote Throttle) - Test