Steering Cylinder - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 199-5815     | 顶出螺栓     | 3     |
ZZ     | 9S-8895     | 螺塞     | 2     |
9S-8896 | 盖     | 2     |
开始:
- 安装转向机架锁。 请参阅拆解和组装, "转向机架锁 - 拆卸和安装"。
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
注: 在所有管路、软管、导线和管子上做出识别标记以便安装。 插接所有管路、软管和管子。 这将有助于防止液体泄漏和防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 断开软管组件 (1) 。
Show/hide table
图 1 | g01191179 |
- 拆下螺栓 (2) (未显示)。
Show/hide table
图 2 | g01191180 |
- 从夹头 (3) 上拆下三个塞。
Show/hide table
图 3 | g01191181 |
- 安装工具 (A) 。 均匀拧紧工具 (A) 以便拆下夹头 (3) 。
- 对下夹头重复步骤 3 和步骤 4。
- 拆下销和垫片。
- 起动发动机。 完全收回转向油缸。 关闭发动机。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
- 断开软管组件 (4) 。
Show/hide table
图 4 | g01191182 |
- 断开软管组件 (5) 。
- 拆下盖 (6) 。
Show/hide table
图 5 | g01191183 |
- 断开软管组件 (7) 。
Show/hide table
图 6 | g01191184 |
- 将适当的起吊设备连接到转向油缸 (8) 上。 转向油缸 (8) 的重量约为 46 kg (101 lb)。
Show/hide table
图 7 | g01191188 |
- 拆下螺栓 (9) (未显示)。
Show/hide table
图 8 | g01191186 |
- 从夹头 (10) 上拆下三个塞。
Show/hide table
图 9 | g01191187 |
- 安装工具 (A) 。 均匀拧紧工具 (A) 以便拆下夹头 (10) 。
- 对下夹头重复步骤 15 和步骤 16。
- 拆下销和垫片。
- 从机器上拆下转向油缸。
- 断开软管组件 (4) 。
Show/hide table
图 10 | g01191189 |
拆解和组装信息
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
B     | 125-0079     | 液压油缸修复台总成     | 1     |
C     | 195-4609     | 油封钩     | 1     |
D     | 7M-7456     | 轴承安装固定胶     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
图 11 | g01191190 |
(1) (6) 安装密封前,将工具 (D) 涂覆到密封槽中。
(2) 将螺栓拧紧至扭矩为 1800 ± 200 N·m (1330 ± 150 lb ft)。
(3) (4) 使用密封的润滑剂润滑密封唇。
(5) 拧紧盖至扭矩为 600 ± 130 N·m (440 ± 95 lb ft)。
Caterpillar Information System:
R1600G Load Haul Dump Braking System Parking Brake - Manual Release
R1600G Load Haul Dump Braking System Brake Disc Wear - Check
140M Motor Grader Engine Supplement Aftercooler - Install
3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Top Speed Is Not Obtained
CS54 and CP54 Vibratory Soil Compactors Hydraulic System Oil Level - Check
3176C, 3406E and 3456 Industrial Engines Engine Shutdown Is Intermittent
CP76 and CS76 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Engine Misfires, Runs Rough or Is Unstable
CP76 and CS76 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
3176C, 3406E and 3456 Industrial Engines Engine Cranks but Does Not Start
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Engine and Machine Warm-Up
3176C Engine for Caterpillar Built Machines ECM Does Not Communicate with Other Modules
R1600G Load Haul Dump Machine Systems Main Control Valve - Remove
R1600G Load Haul Dump Machine Systems Main Control Valve - Install
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Remove
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Install
2007/09/24 An Improved Fuse and ARC Suppressor is Now Used in the Axle Oil Cooler Wiring Harness {1365, 1408}
140H and 160H Motor Graders Changing Direction and Speed
3176C Engine for the R1600G and the R1700G Load Haul Dumps Oil Pressure Is Low
3176C Engine for the R1600G and the R1700G Load Haul Dumps Power Is Intermittently Low or Power Cutout Is Intermittent
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed Control (Remote Throttle) - Test
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Ride Control Accumulator - Test and Charge
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Remove
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Install