Air Inlet Manifold - Remove and Install
拆卸步骤
- 拆卸线束组件盖 (1) 的螺栓 (2) 。 将线束组件盖 (1) 移开。
Show/hide table
 | |
| 图 1 | g01242428 |
- 将适当的起吊设备连在进气歧管 (6) 上。 进气歧管 (6) 的重量约为 91 kg (200 lb)。 拆下螺栓 (3) 。 拆下螺栓 (4) 和螺栓 (5) 。
Show/hide table
 | |
| 图 2 | g01242582 |
- 卸下支架 (10) 。 拆下螺栓 (7) 。 随进气歧管一同拆下弯头 (8) 、 (11) 、密封垫和接头 (9) 。
Show/hide table
 | |
| 图 3 | g02250954 |
- 拆卸进气歧管 (6) 。
Show/hide table
 | |
| 图 4 | g01242585 |
- 对另一侧重复该步骤。
安装步骤
- 将适当的起吊设备连在进气歧管 (6) 上。 进气歧管 (6) 的重量约为 91 kg (200 lb)。 安置进气歧管 (6) 。
Show/hide table
| | |
| 图 5 | g01242585 |
Show/hide table
| | |
| 图 6 | g02250954 |
- 安置密封垫、弯头 (8) 、 (11) 和接头 (9) 。 安装螺栓 (7) 。
注: 确保进气歧管、弯头 (9) 和从后冷器引出的管之间有 3mm 的间隙。 进气歧管和从后冷器引出的管之间的间隙用于防止摩擦。
注: 将弯头 (8) 和 (11) 连接时， 确保弯头 (8) 和接头 (9) 之间有 1mm 的间隙。 确保弯头 (11) 和接头 (9) 之间有 1mm 的间隙。
- 将螺栓 (4) 安装到进气歧管 (6) 上。 安装螺栓 (3) 。 安装螺栓 (5) 。 拆卸适当的起吊设备。
Show/hide table
| | |
| 图 7 | g01242582 |
- 将线束组件的盖 (1) 安置到进气歧管上。 安装螺栓 (2) 。
Show/hide table
 | |
| 图 8 | g01242578 |
- 对另一侧重复该步骤。
Caterpillar Information System:
3512C and 3516C Engines Sensor Supply
C15 and C18 Generator Set Engines Electric Starting Motor - Remove and Install
C175 Generator Set Engines Engine Oil Pump - Install
C15 and C18 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal
C3.3 and C4.4 Rental Generator Sets Additional Messages
Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554} Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554}
CX31 and CX31 HT On-Highway Transmissions General Troubleshooting Information
C15 and C18 Generator Set Engines Alternator - Remove and Install
C175 Generator Set Engines Engine Oil Pump - Remove
C15 and C18 Generator Set Engines Electronic Control Module - Remove and Install
3512C and 3516C Engines Starting Motor System
3512C and 3516C Engines Speed Control
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
3512C and 3516C Engines Analog Sensor (Passive)
C175-16 and C175-20 Engines for Caterpillar Built Machines Fuel Pump (High Pressure) - Remove and Install
C15 and C18 Generator Set Engines Fan Drive - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Sequence Valves - Remove and Install
C3.3 Industrial Engine Air Inlet and Exhaust System - Inspect
C15 and C18 Generator Set Engines Fan Drive - Install
C3.3 Industrial Engine Exhaust Elbow - Remove and Install - If Equipped
C15 and C18 Generator Set Engines Pump Drive - Remove
C15 and C18 Generator Set Engines Pump Drive - Install
C175 Generator Sets Engine Stopping
C15 and C18 Generator Set Engines Fuel Transfer Pump - Remove