Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Usage:
The 7E5085 Fuel Pump Bonnet Retaining Bushing is the service replacement for the 2M4314 Fuel Pump Bonnet Retaining Bushing. The 7E5085 Bushing is coated with a material that requires a lower installation torque.
At installation of the 7E5085 Bushing, tighten it to 163 ± 14 M·n (120 ± 10 lb ft) of torque.
Show/hide table
NOTICE |
---|
Damage to the housing will be the result if the bushing is too tight. If the bushing is not tight enough, the pump will have leakage |
Refer to the Service Manual for removal and installation tools
Caterpillar Information System:
Spring Replacement for Type 2 Fuel Injectors{1250} Spring Replacement for Type 2 Fuel Injectors{1250}
Use of 4C-8701 And 151-1273 Axle Installation Fixture Group{3259} Use of 4C-8701 And 151-1273 Axle Installation Fixture Group{3259}
Use of 4C8753 Extended Collet{1250} Use of 4C8753 Extended Collet{1250}
Using the 7X1700 Communication Adapter Group{0781, 0782} Using the 7X1700 Communication Adapter Group{0781, 0782}
Installation of 4C8246 Dial Indicator to 4C8242 Gage Base Assembly{0760} Installation of 4C8246 Dial Indicator to 4C8242 Gage Base Assembly{0760}
Installation of 4P0371 Rear Gear Group{1206} Installation of 4P0371 Rear Gear Group{1206}
4P4699 Air Separator Group Water Connections{1354} 4P4699 Air Separator Group Water Connections{1354}
Use of 4C4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries{0785, 1401} Use of 4C4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries{0785, 1401}
Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290} Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290}
Installation of 9Y9345 Rear Gear Group With 4W0014 or 1W0024 Rear Housing{1204, 1206, 1212} Installation of 9Y9345 Rear Gear Group With 4W0014 or 1W0024 Rear Housing{1204, 1206, 1212}
Procedures for Using Portable Filter Carts{0680, 5068} Procedures for Using Portable Filter Carts{0680, 5068}
Operator Instruction Card For The Automatic Ether Injection System (AEIS){1456} Operator Instruction Card For The Automatic Ether Injection System (AEIS){1456}
Correct SR1 Polarization for 7E5585 Junction Box{7426, 1908} Correct SR1 Polarization for 7E5585 Junction Box{7426, 1908}
Installation and Maintenance of Gaseous Fuel Filters{1261, 1262} Installation and Maintenance of Gaseous Fuel Filters{1261, 1262}
Installation of 0R3231 Remanufactured 3208 Truck Engine (Natural Aspiration){1000} Installation of 0R3231 Remanufactured 3208 Truck Engine (Natural Aspiration){1000}
Battery Test Sheet Report Battery Test Sheet Report
Jacket Water Heater Installation Procedures{1383} Jacket Water Heater Installation Procedures{1383}
Test and Repair Procedures for 8T0895 Stud Tensioner Cylinder Group and 6V7047 and 5P5247 Hydraulic Puller Assemblies{1000} Test and Repair Procedures for 8T0895 Stud Tensioner Cylinder Group and 6V7047 and 5P5247 Hydraulic Puller Assemblies{1000}
Using the ECAP NEXG4521 Machine Functions Service Program Module{0781} Using the ECAP NEXG4521 Machine Functions Service Program Module{0781}
Bearing Cap Fit for 800 Frame SR4 Generators Using 2L4444 Bearings{4471} Bearing Cap Fit for 800 Frame SR4 Generators Using 2L4444 Bearings{4471}
Using The 4C4069 And 4C4070 Seal Installer{0600, 7555} Using The 4C4069 And 4C4070 Seal Installer{0600, 7555}
Using the 4C6821 Injection Line Speed Pickup Group{0781} Using the 4C6821 Injection Line Speed Pickup Group{0781}
Installation and Operation of 4C9871 Filter Crusher{0616} Installation and Operation of 4C9871 Filter Crusher{0616}
Using the 6I2539 Installation Sleeve{1552} Using the 6I2539 Installation Sleeve{1552}