Rear Suspension Frame - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 1U-9199 | 杠杆式拔拉起吊设备 | 2 |
| B | 1P-0520 | 起子总成 | 1 |
开始:
- 拆下后轴稳定器连杆。 请参阅拆解和组装, "后轴稳定器连杆 - 拆卸和安装"。
- 卸下后驱动轴 。 请参阅拆解和组装, "后驱动轴 - 拆卸和安装"。
Show/hide table
 |
吊装或垫塞不当可能会造成人员伤亡。 当使用起重机或千斤顶顶升任何零件或部件时，与之保持距离。 确保起重机或千斤顶具备正确的部件吊装能力。 在沉重部件下面进行任何工作之前先安装垫块或台架。 图上显示的是部件的近似重量。 清洁要安装零件的所有表面。 |
- 将工具 (A) 和合适的起吊设备连接到后悬架机架 (1) 后部两侧。
Show/hide table
 | |
| 图 1 | g00836188 |
Show/hide table
 | |
| 图 2 | g00834751 |
- 将工具 (A) 和适当的起吊设备连接在后悬架机架 (1) 的前部。 断开润滑脂软管组件 (2) 。
Show/hide table
 | |
| 图 3 | g01202015 |
- 拆卸螺母 (4) 、垫圈 (3) 、螺栓 (5) 和垫圈。
- 使用适当的冲头以拆卸销 (6) 。
Show/hide table
 | |
| 图 4 | g00834753 |
- 拆下将支架 (8) 固定到轴 (9) 和悬架机架上的螺栓 (7) 和垫圈。 需要两个人或使用适当的起吊设备，将支架从机器上拆下。 托架 (8) 的重量约为 35 kg (77 lb)。
Show/hide table
 | |
| 图 5 | g00834754 |
- 将螺栓 (10) 和垫圈从轴 (9) 和悬架机架上卸下。 使用工具 (A) 和适当的起吊设备以将悬架机架从机器上降到适当的支座上。 悬架机架的重量约为 187 kg (412 lb)。
Show/hide table
 | |
| 图 6 | g00834755 |
- 将螺栓 (11) 和垫圈从卡箍环 (12) 上拆下。 拆卸卡箍环 (12) 。
Show/hide table
 | |
| 图 7 | g00834756 |
- 使用工具 (B) 卸下轴承 (13) 。
Show/hide table
 | |
| 图 8 | g00880021 |
Caterpillar Information System:
2002/02/11 Procedure to Purge the Air From the Front Leg Cylinders for the Elevation System {7201, 7562}
2001/10/22 Improved Components for the Heavy-Duty Grain Handling System {692H}
966G and 972G Wheel Loaders Alternate Exit
988G Wheel Loader Steering System Articulated Hitch - Adjust
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 06
2001/10/29 Improved Remanufactured Heavy-Duty Electrical Starting Motors Are Available {1453}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 05
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Pilot Operated)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Mechanically Operated)
2001/10/29 Use the Bearing Preload Tool to Set the Wheel Bearing Preload {4201, 4208}
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Normal Mode
TK1051 Track Feller Buncher Refrigerant Receiver-Dryer - Check
966H Wheel Loader and 972H Wheel Loader Power Train Ground Speed Limiter
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 03
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Cab - Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Power Train Electronic Control System
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 05
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 06
773E Off-Highway Truck/Tractor and 775E Quarry Truck Tire Shipping Pressure
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0422 - FMI 02
2001/11/05 Correction to the Testing and Adjusting Manual for the Power Train {3065}
2001/10/22 Correction to the Operation and Maintenance Manual , "Lubricant Viscosities" {7000, 7581}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0623 - FMI 02
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Detected Fault Mode