Articulated Hitch - Adjust
注: 铰接调整是在操作机器的同时完成的。
参考有关更多说明,请参阅正在维修的机器的维修手册模块拆解和组装, "装载机机架和后部机架 - 分离"和拆解和组装, "装载机机架和后部机架 - 连接"。
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-9754     | 液压千斤顶     | 2     |
B     | 9U-7536     | 起吊台架     | 2     |
4C-5809 | 电动液压泵     | 1     | |
C     | 9U-7536     | 起吊台架     | 2     |
4C-5809 | 电动液压泵     | 1     | |
D     | 1P-0520     | 冲头总成     | 1     |
E     | 1D-5976     | 螺栓 7/8 in - 9 NC x 7 in     | 1     |
2J-3505 | 螺母 7/8 in - 9 NC     | 1     | |
5P-8249 | 垫圈     | 2     | |
1P-1840 | 轴承拆卸工具适配器     | 2     | |
F     | 1D-5976     | 螺栓 7/8 in - 9 NC x 7 in     | 1     |
2J-3505 | 螺母 7/8 in - 9 NC     | 1     | |
5P-8249 | 垫圈     | 2     | |
1P-1841 | 轴承拆卸工具适配器     | 2     | |
G     | 125-0962     | 吊环螺栓     | 1     |
H     | 1U-6343     | 螺杆 M12X1.75 (1)     |
1     |
J     | 6 V     | 深度千分尺     | 1     |
K     | 138-7575     | 连杆支架     | 2     |
Show/hide table
( 1 ) | 制作两根,长度为 254 mm (10 in)。 |
下部铰接组件
Show/hide table
图 1 | g00834526 |
典型实例 (1) 垫片组。 |
Show/hide table
图 2 | g00834532 |
典型实例 上盖 (2) 螺栓。 (3) 盖 |
注: 必须将两个盖都拆下才能够安装轴承拆卸工具适配器。 选择了正确的垫片之后,安装密封。
- 将原有垫片组 (1) 安装到上盖 (3) 下面。 如果安装的是新垫片组,使用 1.55 mm (0.0610 in) 的新垫片组。 用三颗螺栓 (2) 以 120 度的间隔固定上盖。 拧紧螺栓至扭矩为 100 ± 20 N·m (75 ± 15 lb ft)。
- 将工具 (E) 连接到下部铰接的轴承内圈。 使用扭矩扳手和工具 (E) 检查滚动扭矩。 滚动扭矩必须在 5 N·m (44 lb in) 和 15 N·m (133 lb in) 之间。 根据需要,增加或减少垫片。
Show/hide table
图 3 | g00834535 |
典型实例 |
注: 增加垫片会减小滚动扭矩。 减少垫片会增大滚动扭矩。
- 达到正确的滚动扭矩之后,拆下工具 (E) 并安装剩余三颗螺栓 (2) 。 拧紧全部六颗螺栓至扭矩为 100 ± 20 N·m (75 ± 15 lb ft)。
Show/hide table
图 4 | g00834538 |
典型实例 |
上部铰接组件
- 将原有垫片组 (4) 安装到上盖 (5) 下面。 如果安装的是新垫片组,使用 1.55 mm (0.061 in) 的新垫片组。 用三颗螺栓 (6) 以 120 度的间隔固定上盖。 拧紧螺栓至扭矩为 100 ± 20 N·m (75 ± 15 lb ft)。
Show/hide table
图 5 | g00834560 |
典型实例 (4) 垫片组。 |
Show/hide table
图 6 | g00834565 |
典型实例 |
注: 必须将两个盖都拆下才能够安装轴承拆卸工具适配器。 选择了正确的垫片之后,安装密封。
- 将工具 (F) 连接到上部铰接的轴承内圈。 使用扭矩扳手和工具 (F) 检查滚动扭矩。 滚动扭矩必须在 10 N·m (90 lb in) 和 34 N·m (300 lb in) 之间。 根据需要,增加或减少垫片。
Show/hide table
图 7 | g00834570 |
典型实例 |
注: 增加垫片会减小滚动扭矩。 减少垫片会增大滚动扭矩。
- 达到正确的滚动扭矩之后,拆下工具 (F) 并安装剩余三颗螺栓 (6) 。 拧紧螺栓至扭矩为 100 ± 20 N·m (75 ± 15 lb ft)。
Show/hide table
图 8 | g00834575 |
典型实例 |
Caterpillar Information System:
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 06
2001/10/29 Improved Remanufactured Heavy-Duty Electrical Starting Motors Are Available {1453}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 05
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Pilot Operated)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Mechanically Operated)
2001/10/29 Use the Bearing Preload Tool to Set the Wheel Bearing Preload {4201, 4208}
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Normal Mode
TK1051 Track Feller Buncher Refrigerant Receiver-Dryer - Check
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Lift)(Pilot Operated)
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 03
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Center Suspension Frame - Install
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control (LH)
966G and 972G Wheel Loaders Alternate Exit
2001/10/22 Improved Components for the Heavy-Duty Grain Handling System {692H}
2002/02/11 Procedure to Purge the Air From the Front Leg Cylinders for the Elevation System {7201, 7562}
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Rear Suspension Frame - Remove
966H Wheel Loader and 972H Wheel Loader Power Train Ground Speed Limiter
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 03
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Cab - Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Power Train Electronic Control System
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 05
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0421 - FMI 06
773E Off-Highway Truck/Tractor and 775E Quarry Truck Tire Shipping Pressure
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0422 - FMI 02