Center Suspension Frame - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0520     | 起子总成     | 1     |
B     | 1U-9200     | 操纵杆滚轮起重机     | 3     |
Show/hide table
吊装或垫塞不当可能会造成人员伤亡。 当使用起重机或千斤顶顶升任何零件或部件时,与之保持距离。 确保起重机或千斤顶具备正确的部件吊装能力。 在沉重部件下面进行任何工作之前先安装垫块或台架。 图上显示的是部件的近似重量。 清洁要安装零件的所有表面。 |
- 清洁并检查所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
- 利用工具 (A) 安装轴承 (16) 。
Show/hide table
图 1 | g00879868 |
- 安置卡箍环 (15) 并安装螺栓 (14) 和垫圈以便安装卡箍环。
Show/hide table
图 2 | g00834277 |
- 将工具 (B) 连接到机器两侧中间悬架机架 (3) 后部,如图所示。 中间悬架机架 (3) 的重量约为 192 kg (422 lb)。
Show/hide table
图 3 | g01201913 |
Show/hide table
图 4 | g01201928 |
Show/hide table
图 5 | g01201931 |
- 将工具 (B) 连接到中间悬架机架 (3) 前部,如图所示。 中间悬架机架 (3) 的重量约为 192 kg (422 lb)。 使用工具 (B) 以将中心悬架机架 (3) 提升到位。
- 安装销 (9) 。 使用适当的冲头以便安装销 (9) 。
Show/hide table
图 6 | g00834253 |
- 安装螺栓 (8) 、垫圈 (6) 、螺母 (7) 和垫圈。
Show/hide table
图 7 | g00834232 |
- 连接润滑脂软管组件 (5) 。
- 安装螺栓 (13) 和垫圈,以便将轴 (12) 连接至中心悬架机架。
注: 可能需要让螺栓保持松开,直到悬架机架连接到每个位置。
Show/hide table
图 8 | g00834271 |
- 让两个人一起或使用适当的起吊设备,将支架 (11) 安置到机器上。 支架 (11) 的重量约为 35 kg (77 lb)。 安装将支架固定到轴 (12) 和悬架机架上的螺栓 (10) 和垫圈。
Show/hide table
图 9 | g00834267 |
- 润滑步骤 6 中安装的销 (9) 。 请参阅操作和保养手册, "悬架和悬架油缸轴承 – 润滑"。
- 安装螺栓 (4) 。
Show/hide table
图 10 | g00834187 |
- 将盖 (2) 安装到悬架机架 (3) 任一侧,然后安装螺栓 (1) 。
Show/hide table
图 11 | g00834178 |
End By: 安装中轴稳定器连杆。 请参阅 拆解和组装, "中轴稳定器连杆 - 拆卸和安装"。
Caterpillar Information System:
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control (LH)
2001/11/05 A New Shaft And Longer Bolts Are Now Available For The Fan Drive Bracket {1359}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0419 - FMI 06
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control (RH)
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Oil Filter (Power Train)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control (LH)
3056 Engines Main Bearing Journal
3056 Engines Connecting Rod Bearing Journal
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control (RH)
980G Wheel Loader Power Train Transmission Planetary - Assemble
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Bypass Switch (Power Train Oil Filter)
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Cab - Remove
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 03
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Lift)(Pilot Operated)
TK1051 Track Feller Buncher Refrigerant Receiver-Dryer - Check
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Normal Mode
2001/10/29 Use the Bearing Preload Tool to Set the Wheel Bearing Preload {4201, 4208}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Mechanically Operated)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Pilot Operated)
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 05
2001/10/29 Improved Remanufactured Heavy-Duty Electrical Starting Motors Are Available {1453}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0420 - FMI 06
988G Wheel Loader Steering System Articulated Hitch - Adjust
966G and 972G Wheel Loaders Alternate Exit