Drive and Steering Axle (Rear) - Remove
Removal Procedure
Start By:
- Remove the rear tires and wheels. See Disassembly and Assembly, "Tires & Wheels (Rear) - Remove and Install".
- Remove two brackets (3) for the front of the drive shaft. Remove four bolts (4) from the rear of the drive shaft.
Show/hide table
 | |
| Illustration 1 | g00779594 |
- Remove 2 bolts (16) and pin (17) in order to remove parking brake assembly (18) .
Show/hide table
 | |
| Illustration 2 | g00775573 |
- Remove 2 hydraulic hoses (11) from rear steering cylinder (12) .
Show/hide table
 | |
| Illustration 3 | g00775540 |
- Remove 2 hydraulic hoses (13) from the top of the axle.
Show/hide table
 | |
| Illustration 4 | g00775484 |
- Remove 2 bolts (14) from bracket (15) for the manifold. Repeat for the other side of the bracket for the manifold.
Note: Be sure to support the manifold and the bracket.
Show/hide table
 | |
| Illustration 5 | g00775534 |
- Disconnect the wire for the sensor for the rear steer.
Note: The wire is located in the area of the pointer.
Show/hide table
 | |
| Illustration 6 | g00775570 |
- Position a suitable hydraulic jack (19) under the rear axle.
Show/hide table
 | |
| Illustration 7 | g00775593 |
- Remove 4 nuts (20), the washers, and the plate. Repeat for the other side.
Show/hide table
 | |
| Illustration 8 | g00775604 |
- Use a suitable lifting device in order to move the axle.
Note: The axle weighs approximately 500 kg (1102 lb).
Show/hide table
 | |
| Illustration 9 | g00775608 |
- Place the axle on a suitable table.
Use suitable tie-downs in order to secure the axle.
Show/hide table
 | |
| Illustration 10 | g00775617 |
- Remove bracket (21) for the parking brake.
Show/hide table
 | |
| Illustration 11 | g00775620 |
- Remove 3 bolts (22). Remove cover (23) .
Show/hide table
 | |
| Illustration 12 | g00775621 |
- Remove clip (25). Remove pin (26) and washer (27) .
Show/hide table
 | |
| Illustration 13 | g00775627 |
- Remove 3 bolts (29) and the washers. Remove the sensor and bracket (28) .
Show/hide table
 | |
| Illustration 14 | g00775630 |
Caterpillar Information System:
12H, 140H, 143H, 160H and 163H Motor Graders Power Train Differential
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Piston Pump (Auxiliary) - Remove
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Fuel Tank Water and Sediment - Drain
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Piston Motor (Drag Conveyor) - Install
143H and 163H Motor Graders Kingpin Bearings - Lubricate
2001/04/16 A New Track Adjuster Valve is Available {5051}
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Hydraulic System Oil Filter - Replace
322C Excavator Machine System Specifications Stick Cylinder Lines
2001/06/18 Correction to the Service Magazine , "The Product Identification Number (PIN) and the Plate for the Product Identification Number (PIN) will Change" {7557}
735 Articulated Truck Fuel System Secondary Filter - Replace
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Hydraulic System Oil - Change
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Piston Motor (Drag Conveyor) - Remove
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Piston Pump (Auxiliary) - Install
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Hydraulic System Oil Level - Check
2001/07/09 Improved Grapple Tongs Are Used on Forwarders {6307}
120H and 135H Motor Graders Moldboard Wear Strip - Inspect/Adjust/Replace
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Hydraulic Cylinder (Tow Point) - Remove and Install
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System MID 081 - CID 0070 - FMI 04
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power Train Drive and Steering Axle (Rear) - Install
12H, 140H, 143H, 160H and 163H Motor Graders Power Train Final Drive
735 Articulated Truck Radiator Core - Clean
735 Articulated Truck Oscillating Hitch - Lubricate
2001/04/02 Correct Belt Tension is Necessary in Maintaining Service Life of V-Belt {1357, 1405, 7450}
2001/02/26 A New Shift Solenoid Increases Reliability {3174}