Correction to the Special Instruction for the Installation of the Bevel Gear, Differential and the Differential Case {3256, 3258}
- Earthmoving Compactor:
- 835 (S/N: 44N1-UP)
- Landfill Compactor:
- 826B (S/N: 58U1-UP)
- Soil Compactor:
- 825B (S/N: 43N1-UP)
- Off-Highway Truck/Tractor:
- 768B (S/N: 79S1-UP)
- Wheel Loader:
- 980 (S/N: 42H1-UP)
- Wheel Tractor:
- 824 (S/N: 29G1-UP)
- Wheel Tractor-Scraper:
- 619C (S/N: 61F1-UP; 62F1-UP)
- 769B (S/N: 99F1-UP)
- 980B (S/N: 89P1-UP)
- 988 (S/N: 87A1-UP)
- 992C (S/N: 42X1-UP; 49Z1-UP)
- 992B (S/N: 25K1-UP)
- 824B (S/N: 36H1-UP)
- 834 (S/N: 43E1-UP)
- 621 (S/N: 15U1-UP; 23H1-UP)
- 623 (S/N: 52U1-UP)
- 627 (S/N: 54K1-UP; 68M1-UP; 50K1-UP; 69M1-UP)
- 627B (S/N: 37V1-UP; 38V1-UP)
- 630A (S/N: 52F1-UP)
- 631A (S/N: 51F1-UP)
- 631B (S/N: 13G1-UP)
- 631C (S/N: 67M1-4418)
- 632 (S/N: 14G1-UP)
- 633 (S/N: 44J1-UP)
- 633C (S/N: 66M727-UP)
- 637 (S/N: 65M1-386; 79P1-429; 64M1-UP; 91N1-UP; 92N1-UP)
- 637B (S/N: 26R1-UP)
- 657 (S/N: 19G1-UP)
- 657B (S/N: 47M1-205; 53K1-778)
- 666B (S/N: 20G1-268)
- Inspect the dowel holes in the bevel gear and the differential case. Ensure that the holes are aligned. Install the 1S-9292 Dowels. Ensure that the dowels fit correctly.
Note: Ream the holes to the correct dimensions if there is a problem with the alignment or the fit. Refer to Table 1 for the correct dimensions. Install new 7D-0227 Dowels in the holes that were reamed.
Caterpillar Information System:
725 and 730 Articulated Trucks Power Train Interaxle Differential
725 and 730 Articulated Trucks Power Train Transmission Planetary
725 and 730 Articulated Trucks Power Train Oil Filter (Transmission)
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0709 - FMI 03
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0704 - FMI 04
797B Off-Highway Truck Power Train Rear Axle and Final Drive Hydraulic System
3176C Engine for Caterpillar Built Machines Ether Injection System - Test
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0704 - FMI 03
C-15 and C-16 Industrial Engines Fuel Transfer Pump
2000/12/18 A New Schematic for the Hydraulic System is Available {5050}
424D, 428D and 438D Backhoe Loaders Before Operation
2000/12/01 Correction to Testing and Adjusting Module, SENR5832, Electronic Modular Control Panel II+ (EMCPII+) for MUI Engines {4490}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Lift Arms - Remove
725 and 730 Articulated Trucks Braking System Parking Brake Air - Purge
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Low Power/Poor or No Response to Throttle
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Poor Acceleration or Response
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0709 - FMI 05
938G Wheel Loader and IT38G Integrated Toolcarrier Power Train Check Valve (Axle Oil Cooler Bypass)
3126B Engine for Caterpillar Built Machines Diagnostic Codes
424D, 428D and 438D Backhoe Loaders Boom Transport Lock
3126B Engine for Caterpillar Built Machines CID 0041 FMI 03 8 Volt DC Supply short to +batt
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0709 - FMI 06
3406E Engine for Caterpillar Built Machines CID 0041 FMI 04 8 Volt DC Supply short to ground
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0724 - FMI 03